Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Impulse buy 45 comments/advice sought *LINK*

Posts

Impulse buy 45 comments/advice sought *LINK*

#1

Impulse buy 45 comments/advice sought *LINK*

eric

>I have been wanting one of these as a user for a while and wasn't having any luck finding one in the wild so started following them on the auction site.

This one appeared to be in good condition and the price reasonable as compared to the others I had tracked through the completed items listing.

Time to confess that I didn't do any extensive research on Stanley 45's in general before purchasing this one. My rough estimate from reading posts on 45's on this forum is that it is complete complete in that it has two sets of rods, cam stop, slitter and slitter depth stop, and the box of blades.

So my questions to those who are knowledgable about the 45's are -

From the pictures is anything abviously missing?

Can anyone hazard a guess as to why so few bidders and the relatively low price? Some of the ones that I thought were comparable went for a lot (>50%) more. In other words, what did I miss.

And finally, did I mess up or does it appear that I got a servicable usergrade tool?

Thanks,

Eric, who use this rather than an electron eater on a couple of projects.


Impulse Purchase

Re: Impulse buy 45 comments/advice sought *LINK*

#2

Jack Guzman from Maine

Re: Impulse buy 45 comments/advice sought

Jack Guzman from Maine

>That's a decent looking tool for the money. I've noticed that 45s are going pretty cheap lately.I got one a week ago for $61 but it doen't look as nice as yours. --Jack

Re: Impulse buy 45 comments/advice sought *LINK*

#3

Re: Impulse buy 45 comments/advice sought

Peter L Berglund in Denver

>Looks pretty fine to me, Eric. A lot nicer than mine, which I bought a few years ago for about $10 less, a little less knowledgeable than I am now. Mine's missing the cam and slitter, which I understand is a common deficit, and my nickel plating is not nearly is nice...

Some of the others can tell you if your price is appropriate. Todd?

Peter

Re: Impulse buy 45 comments/advice sought *LINK*

#4

It's missing...

Scott Burr in Ben Lomond CA

>The screwdriver, adn the orignal box. It apprers to be a newer 45, witch might explane the price. All in all I'd say you got a good deal. My sweetheart 45 cost alot more...

Re: Impulse buy 45 comments/advice sought *LINK*

#5

ok for a 45

Dennis

>Iam no fanboy of the 45, have had one for over 25 years and used it maybe 3 times. From what i see and run into that is not bad price for what the dealer shows. The hollow and rounds you can add for a price, and every now and then the chestnut box shows up for them.

Just sometimes everybody is sleeping when the auction closes.

Dennis,who thinks you can get more" bang for the buck" than a 45 like that.

Re: Impulse buy 45 comments/advice sought *LINK*

#6

Re: Impulse buy 45 comments/advice sought

David Miller from Iowa

>I collect em and watch them constantly on eBay. You got it for the going rate and it would have been a long time before you found one like that in the wild. Looks like a Type 16 made from 1936-1948. One of the more common types with an estimated 80,000 made. If you like this minutuae, get Dave Heckel's book.

You did good. Spend some time getting up the learning curve and you will use it a lot. Remember though - you must use it on very straight grained, very clear wood. If you cheat on that you will have nothing but trouble.

David

Re: Impulse buy 45 comments/advice sought *LINK*

#7

Slight disagreement from limited experience

Bill Houghton, Sebastopol, CA

>Granted, it was redwood, but I found when making the porch rails this Spring that I could plane through some small knots and grain irregularity if I was patient.

Blemish-free and up-grain in the right direction is of course easier, but isn't that always true?

Re: Impulse buy 45 comments/advice sought *LINK*

#8

You done good!

Don Thompson - Cutler Ridge, Florida

>From what I can tell, you have all of the parts that would have come with the plane when purchased new.

There are other, extra-cost accessories, such as the hollow and round sets, and the special cutters.

Re: Impulse buy 45 comments/advice sought *LINK*

#9

Thank you

eric

>Thanks everyone.

I'm very glad that this seems plane appears complete and in good shape. Usually, I end up with regrets over impulse buys on things I think look like good deals.

Heckel's book sounds like a great idea, I will have to track down a copy.

I can't wait for it to show up and start using it. I have some nice walnut and butternut scraps set aside to start the learning process on.