Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

The Old Stone Spins

Posts

The Old Stone Spins

#1

The Old Stone Spins

Todd O. Cronkhite Native of Maine

>Set about making the supports for that old grindstone I have with the square center tonight. Got them made,and got it mocked up sitting on my workbench right now. I must say I felt a certain excitement when I gave it a spin and watch it rotate. Now tellin' when it last spun. The old fellow I got it from said it was laying in the bushes when he bought the place in '59, so it's been at least that long for sure. The stone is a bit out of round, and I'm wondering if I should true it up or not. Guess I'll first see just how bad it is and decide from there. Hate to waste away to much of it just to true it up. What do ya' all think?

Had to custom fit the wooden center block as the hole in the stone is quite crude. I made the center out of two 2x4's screwed together, than bored a 3/4" hole thru the center which I passed a length of 3/4" piece of all thread thru. I made large plwood disks to put up against the stone and than snugged up both sides with a lockwasher and a nut. Where the all thread goes into the supports I put in a piece of conduit to protect the wood from getting chewed to bits by the threads. Tomorrow I'll put a foot on each of the supports and bolt it to a piece of plywood for now so that it ban stand by its self. I'll also make a handle to put on one end of the all-thread so I can crank it.

My idea is to also make a bench for it that I can bolt it too so I can use it as a treadle sharpener as well. I know that the old man will be thrilled to see it work as a hand cranker, and I can't wait to finish it and show it to him this weekend.

Todd O.

Re: The Old Stone Spins

#2

Re: The Old Stone Spins

Joe Rogers, Northern Virginia

>Any chance that you could offset drill the block that you make for the center to minimize the runout?

That way you could save some of that sandstone.

IIRC when my cousin in Illinois used a big grindstone he had a sit on stand and got his crotch soaked from the water that spilled off the stone.

I (at the age of 7 or 8) thought it was sooo funny that he looked like he had an "accident".JR

Re: The Old Stone Spins

#3

Re: The Old Stone Spins

Todd O. Cronkhite Native of Maine

>I really doubt it Joe, but the thought did cross my mind to try to put shims under one suppoert to see if that would help some.

I, like you, don't want to waste much of it wither, as it is only about 5" fromthe center now. It is 13" across, and 2 1/2" inces wide. I do need to dress the face as it looks like somebody used it to sharpen gouges and held it in just one place thus wearing a groove.

Tomorrow I'll rig up a pencil in a stand. hold it against one side, rotate it and see what I get for a line. Maybe when I dress it that'll be enough to true it as well. Sure is a nice little sandstone tho, and looks even nicer sitting in supports. I've gone out to the garage twice now just to look at it.

Todd O.

Re: The Old Stone Spins

#4

Steve Kubien

Re: The Old Stone Spins

Steve Kubien

>I know where a similar stone is waiting to be bought. It is already mounted and is WAAAAAY off centre. This beast is about 4" across and 14-18" in diameter (maybe more, I didn't measure). There is lots of good stone left but I do not know how to true it. Can somebody fill me in?

Thanks,

Steve Kubien

Ajax, Ontario

Re: The Old Stone Spins

#5

Re: The Old Stone Spins

Moses Yoder in White Pigeon, MI

>I saw an old treadle grindstone at a garage sale this year. The guy had $700 marked on it. I simply could not keep myself from laughing out loud when I saw the price tag.

Re: The Old Stone Spins

#6

Re: The Old Stone Spins

Bob Hackett

>I`ve heard that you can true them by using an old pipe to dress them into round.

Clamp a bar or board across for a rest and just slowly roll the pipe back and forth till the high spot`s gone.

It`ll take either 2 people or sacrificing some electrons to do the truing as you need to stay steady with that pipe.

Mainely,Bob

Re: The Old Stone Spins

#7

Re: The Old Stone Spins

Steve Jenkins, Dallas TX.

>remember when I was a kid we had an old grindstone with a metal seat and pedals. Can't remember how big it was but I'm sure it was a couple feet in diameter at least. Think I'll ask my bro if it's still in the shed out back. Steve

Re: The Old Stone Spins

#8

One option

David Miller from Iowa

>A number of years ago, my Dad gave me a treadle powered grindstone he got at a sale for a couple bucks. It was maybe a 26" diameter, but had a big flat spot where it sat in the water tray and decomposed. I set up a stablizing jig (Workmate) and used a belt sander to round it out. The trick was getting the sander locked onto the Workmate so it didn't move in and out (clamps and blocks). Worked good and the stone came out perfectly round. Although it was a three person operation - Boy #2 ran the pedals, Boy #1 stood on the Workmate, and I ran the sander.

Re: The Old Stone Spins

#9

Steve, your teasin' again

Todd O. Cronkhite Native of Maine

>4" across? Gadzooks, are you sure it's not some type of milling stone? Sounds like a good companion for my slicks.

Just so happens that sharpening stones is one of favorite items, so I am tickled pink to get this old beast back into the game.

Please put the slick close to the stone when you get it ( and I know you will)to assist in my quick get-a-way. ;~)

Todd O.