Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

1ST ATTEMPT AT PLANE REHAB

Posts

1ST ATTEMPT AT PLANE REHAB

#1

1ST ATTEMPT AT PLANE REHAB

Gerry Doll

>Following the advise of the galoots on this board, started inquiring of friends re: old tools. A colleague submitted a #6 of his father's (either the devil's jack plane, per Sir Patrick, or a Nancy boys joiner per the archive)

Pretty grunged up, surface rust, but sole appears flat and square to the sides. Used Simple Green to clean grunge, and Naval jelly to get rust off iron and chip breaker. (May need to order replacement from the Eminent Sr. Hock) Have had excellent result using automotive valve lapping compound (120 and 280 grit) on surface where frog meets casting.

About 80 of original finish remains on base. On areas where it has flaked and peeled away, surface rust. Will attempt to remove with brass brush. This is to be a user, as I am lacking a joiner.

???? After removing rust from top of casting, next step? Oil it? WD40? Spot paint paint bare areas with Rustoleum??? Polish with the untainted blood of vestal virgins?

Appreciate any assistance.

Gerry

P.S. Kudos to Bugbear for the info and links on his site re: Plane restoration.

Re: 1ST ATTEMPT AT PLANE REHAB

#2

Check out this WC article  *LINK*

Dan Donaldson

>


Restoring Planes

Re: 1ST ATTEMPT AT PLANE REHAB

#3

Re: Check out this WC article

Todd O. Cronkhite Native of Maine

>Well Gerry, it won't be long now and you'll be living in a van down by the river with a bunch of tools.

Started out with a #6 eh? GOOD ON YA! I don't care what Patrick says I like the #6.

Now than, take that insidous Naval Jelly and throw it straight into the Hazmat Recycle bin. that stuff is bad, bad, bad joo-joo. Will blind you real QUICK, and I don't think it does the tool much good either. Think CAUSTIC CHEMICAL bad, bad, bad stuff.

I[ve never tried simple Green, or SOS pads, lapping grits and all hate jazz, so I can't speak on it, but I can speak on Electrolysis, and can highly recommend it.

By hook, or my Crook get your philangies on a copy of WOOD mag issue #63. (Sept. 93) Turn to page 74, and there you will find the best, bar-none instructions for electroylis.

If you can't get a copy, send me your snail mail address and I'll send you or anybody else a copy.

Todd O.

Re: 1ST ATTEMPT AT PLANE REHAB

#4

Re: 1ST ATTEMPT AT PLANE REHAB

Todd Hughes

>While maybe OK for taking the rust off lawn chairs that you are going to paint,[I wouldn't even use it for that!] Naval Jelly is pretty bad stuff to use on any tools because it leaves a dead dull grey look to the steel as you no doubt have found out.Actually believe it is some type of acid,[phosphoric?] that is the main coponet of the Naval Jelly and I believe it can lead to further rusting.

When i clean a plane I like to use sand paper on a sick and go from front to back in one direction and a fine wire wheel to gently remove any loose rust.Steel wool can be used to get to areas that are hard to reach.I wouldn't do any "painting" on any plane esp. one that still has 80% of it's original finish.I clean a plane so that it is clean but doesn't look like it has been cleaned and think many guys over do it trying to make a well used plane look "New" and in the end wind up with a fake looking over cleaned plane......Todd

Re: 1ST ATTEMPT AT PLANE REHAB

#5

Hey Todd

Todd O. Cronkhite Native of Maine

>what cha' doin' foolin' about on the 'puter at this time of day?

Todd O.

Re: 1ST ATTEMPT AT PLANE REHAB

#6

Re: Check out this WC article

Gerry Doll

>I wish I caught your response earlier re: Jelly.

Was followin recomendation from Traditional tools, re: phosphoric acid to remove rust. http://www.traditionaltools.us/forum/viewtopic.php?t=290,

It did leave the chip breaker and iron pretty discolored.

Re: 1ST ATTEMPT AT PLANE REHAB

#7

Re: Hey Todd

Todd Hughes

>Am going over to D.C. later to see the Miss D. and figured I would stay here at Joannes,[she went to the Flea Market] this morning and sort though the boxes of tools I bought yesterday at Auction....Yea thats a tease!...[how about a box of 30 plow plane irons for $20, eh?].....Todd

Re: 1ST ATTEMPT AT PLANE REHAB

#8

Re: Hey Todd

Dale Stansbery

>I've finally figured out what you mean by "old tool heck". You must have a heck of a time figuring out what not to buy from all the tools available.

Re: 1ST ATTEMPT AT PLANE REHAB

#9

SOLD!!

Todd O. Cronkhite Native of Maine

>how about a box of 30 plow plane irons for $20, eh?

I'll send a money order first thing in the morning! ;~)

Todd O.

Re: 1ST ATTEMPT AT PLANE REHAB

#10

Common mistake Gerry

Todd O. Cronkhite Native of Maine

>Been there done that myself. Back in the early 90's loooooooooooooong before I had internet, or even a computer I derusted a large miterbox saw using Naval Jelly. Actually that's a lie, I derusted only one side of the saw as I had had enough of that sh!t almost as soon as I started. Left my saw with a dull grey side. Was so annoyed I hung it on a nail and there it stayed for years.

Hey, what's a fella to do, if he don't know, he don't know, so he does what he thinks is right and learns one way or the other something new.

thank Goodness for the internet and forums such as this one eh Gerry.

I remeber the first time...................oops, best save that story for when we are talking face to face eh? ;~)

Todd O.

Re: 1ST ATTEMPT AT PLANE REHAB

#11

to late I'm

Ernie Miller Topeka

>PayPaling today!

Re: 1ST ATTEMPT AT PLANE REHAB

#12

Re: 1ST ATTEMPT AT PLANE REHAB

paul womack

>P.S. Kudos to Bugbear for the info and links on his site re: Plane restoration.

Happy to help.

BugBear