Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

New hand tools at IWF

Posts

New hand tools at IWF

#1

New hand tools at IWF

Christopher Schwarz

>I've been soaking up a lot of the new products here at IWF in Atlanta this week. And while most of the machines are bigger than my pick-up truck (and cost 10 times as much) there are some very nice and new hand tools on display.

At the Lie-Nielsen booth, Deneb, Joe and the family are showing off a new low-angle block plane. It's the 102 (a fixed-mouth plane) but in ductile iron with a bronze lever cap. I believe the price is $70. I very much like this pattern and the plane looks very nice. It's a great entry-level tool.

Also hiding in the back of the Lie-Nielsen booth was a 1/2" mortise chisel. It's a 750 pattern socket chisel with a hornbeam handle.

And they have one of the new workbenches that are going to begin selling. I could blather on a very long time about the high points, but here are a couple: a quick-release face vise with wooden jaws (the vise has been modified in several interesting ways). The bottom of the tool tray is removable for clamping things to your benchtop. And there's a shoulder vise on the right. I'm told that the beauty of these benches is they can be built to the customer's specifications for height, length and vise placement.

The Lee Valley booth was also filled with goodies (and yes Rob Lee is here). The large shoulder plane was out and they were taking orders. It's 1-1/4" wide, 8-1/4" long and weighs almost four pounds. It has the same style grip at the rear with a movable front wooden knob that has four positions. Very nice. $169.

Also, Lee Valley has long been on a quest to produce reasonably priced straightedges. They're in stock now. The aluminum one is 24", straight to .003" and $19.50. The steel one is 24" straight to .001" (over the entire length) and $36.50.

Tucked in the corner of the Trend booth, the British have produced their own domestically made diamond sharpening stones. These are being made for them by a supplier to Rolls Royce and the massive plates are flat to .0005" corner to corner. Yes, that is half a thou.

The plates are smart in a lot of ways. There are only two grits. A coarse and a fine. And judging from the time I spent with them yesterday, they really understand the diamond medium and hand tool sharpening. I'm going to be testing these for a future issue.

There's more, but I have to save some ink for my employer.

Chris

Re: New hand tools at IWF

#2

Re: New hand tools at IWF

Matt Prusik

>Nice Report. Wish I could have gone to the IWF this year. But I just was not able to make it from NJ due to family obligations.

One thing about the Aluminum straightedges though. Did they address the issue of whether it will stay within 0.003 if it's dropped on say a concrete floor? I have seen a lot of Al dented up that way and be "less usable" in metalshop class. I can just wonder what would happen to a straightedge!

Matt Prusik

Re: New hand tools at IWF

#3

Re: New hand tools at IWF

Bill Murphy / Reading Pa.

>Hi Christopher,

Great review, I look forward to the full article with pictures.

You have one of the best jobs in the world.

Bill Murphy

Reading,PA.

Re: New hand tools at IWF

#4

Re: New hand tools at IWF

Christopher Schwarz

>Matt,

I didn't ask Rob Lee about its durability, but I doubt that either straightedge would fare well after a fall. Also, the aluminum straightedge is not for knifing joints. However, I've had an aluminum straightedge for four years now and it has been excellent for machine setups and testing shot edges, assemblies, plane bottoms etc.

However, at that price, I'll be buying a steel one, too now.

One more thing to report: I got a good look at the sets of try squares from Gladstone Tools (Manny's Woodworking store in Lexington, Ky.).

I was impressed with the weight, fit and finish, markings and satin blade. I had no way of testing the squares at the show, but they looked like excellent bargains.

I actually owe a big debt to Manny (who was at IWF). When I took my first woodworking class in 1993 with Lynn Sweet, I lived at Manny's store on Saturdays. It was the only place I'd ever seen a Japanese saw, chisel or sharpening stone in the flesh. And the book selection there is the best I've ever seen anywhere. He gets stuff (even out of print stuff) that no one else does.

I'll be testing those squares soon I hope.

Chris

Re: New hand tools at IWF

#5

Mark Meier (Ann Arbor, MI)

Re: New hand tools at IWF

Mark Meier (Ann Arbor, MI)

>Thanks for the report, Chris. I'd guess the new L-N 102 in iron must be to compete with the Veritas Apron Plane at the same price level. I can't recall the exact ratio but I think I heard it costs L-N over 2x more to use bronze than iron for the plane bodies.

Mark