millers falls eggbeaters

5/30/04, 5:57 PM #1

Jack Guzman from Maine
Member
Offline
3,329 posts

Registered: 5/9/04

millers falls eggbeaters

Jack Guzman from Maine

>I picked up a MF #2A eggbeater hand drill. It's missing the side knob and I'd like to make one.I found pictures of it on a google search but I would like dimensions. Does anyone have one of these and could you measure yours? I need the thickness at the widest point and the length of the knob itself.I'm thinking of glueing a piece of threaded rod or a bolt with the head cut off into a turned knob.Thanks---Jack

- - -

I am a carpenter by trade.Also a handyman/Jack -of-all-trades.I work around my neighborhood mostly helping people keep up their old houses.I have a fairly large woodworking shop in my house where I work with both hand and power tools. At the moment I'm focusing on Windsor chairs building.I will build most anything if needed. I'm always learning,adapting,changing trying to broaden my woodworking skills.I work mostly with hand tools in my shop but will use power if it is a better way to get the desired result. My wife,Donna,and I live in the woods of Maine with our dogs,cats,and birds. We have 5 grown kids and six grandchildren. Woodcentral has been central to my growth as a woodworker. I pass through this place every day.

Re: millers falls eggbeaters

5/30/04, 7:24 PM #2

Scott Burr in Ben Lomond CA
Member
Offline
3,699 posts

Registered: 1/5/04

Here's the dimensions of a

Scott Burr in Ben Lomond CA

>5A if that helps. Length=1 3/4. Small dia.=3/4". Large dia.=1 3/8"

Hope this helps, Scott

Re: millers falls eggbeaters

5/30/04, 7:30 PM #3

Andy Lincoln,in Dearborn,MI
Guest

Re: millers falls eggbeaters

Andy Lincoln,in Dearborn,MI

>Jack,

Side knob on an MF #2:

large dia =1.410"

small dia(includingO.D.of ferrule)=.735"

Over all length - threaded stud=1.810"

Andy

Re: millers falls eggbeaters

5/30/04, 8:25 PM #4

Jack Guzman from Maine
Member
Offline
3,329 posts

Registered: 5/9/04

Re: millers falls eggbeaters

Jack Guzman from Maine

>That's the one I was looking for. Thanks ---Jack

- - -

I am a carpenter by trade.Also a handyman/Jack -of-all-trades.I work around my neighborhood mostly helping people keep up their old houses.I have a fairly large woodworking shop in my house where I work with both hand and power tools. At the moment I'm focusing on Windsor chairs building.I will build most anything if needed. I'm always learning,adapting,changing trying to broaden my woodworking skills.I work mostly with hand tools in my shop but will use power if it is a better way to get the desired result. My wife,Donna,and I live in the woods of Maine with our dogs,cats,and birds. We have 5 grown kids and six grandchildren. Woodcentral has been central to my growth as a woodworker. I pass through this place every day.

Re: millers falls eggbeaters

5/30/04, 8:27 PM #5

Jack Guzman from Maine
Member
Offline
3,329 posts

Registered: 5/9/04

Re: Here's the dimensions of a

Jack Guzman from Maine

>I just checked and yes,that's the same one.Thanks---Jack

- - -

I am a carpenter by trade.Also a handyman/Jack -of-all-trades.I work around my neighborhood mostly helping people keep up their old houses.I have a fairly large woodworking shop in my house where I work with both hand and power tools. At the moment I'm focusing on Windsor chairs building.I will build most anything if needed. I'm always learning,adapting,changing trying to broaden my woodworking skills.I work mostly with hand tools in my shop but will use power if it is a better way to get the desired result. My wife,Donna,and I live in the woods of Maine with our dogs,cats,and birds. We have 5 grown kids and six grandchildren. Woodcentral has been central to my growth as a woodworker. I pass through this place every day.

millers falls eggbeaters

Posts