Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

10,000 grit stone...feedback? *LINK*

Posts

10,000 grit stone...feedback? *LINK*

#1

10,000 grit stone...feedback? *LINK*

Joe Hurst

>Hey Guys-

I didn't think that waterstones went much higher than 8,000. Now I see that someone's offering a 10K (see link).

Anybody have any experience with this Ice Bear stone? Truth be told, most of my tools could use a little time on my lower-grade stones, but once you start chasing the "ultimate" edge, it's kinda hard to stop.


10,000 Grit Stone

Re: 10,000 grit stone...feedback? *LINK*

#2

Re: 10,000 grit stone...feedback?

Steve knight

>I would not waste your money. I have not seen a sharp difference between 8000 and 12000 shapton stones.

your tool will only get so sharp and thats it no matter how fine of a grit you go to. a japanese steel will benifit more then other steels because it is usualy harder and will get sharper.

so don't waste your time. to get a tool sharper spend more time flattening and sharpening accuratly.

Re: 10,000 grit stone...feedback? *LINK*

#3

Re: 10,000 grit stone...feedback?

Christopher Fitch @ Memphis

>After reading the link and advertising material, I'm not sure why they are making a big deal over less than 1 micron size.

3M makes lapping film and micro-abrasive sheets that are graded down to 0.1 micron in size. You can find them online at stores all over the internet. I use the 0.5 grit sheets that Lee Valley sells. As Steve pointed out, Shapton sells a 12000 grit stone now.

As to grit size, going above 8000 grit seems kind of pointless in my mind. Recently I even read that beginner's should focus on getting good results using up to 4000 grit stones since 8000 grit stones can be quite expensive.

just my thoughts...

Also, Joel at toolsforworkingwood sells the Ice Bear stone in question. Perhaps he can chip in with his views...

Re: 10,000 grit stone...feedback? *LINK*

#4

The Shaptons go up to 30,000, for a price.  *LINK*

Pam Niedermayer - Austin, TX

>


Shapton stones

Re: 10,000 grit stone...feedback? *LINK*

#5

Re: 10,000 grit stone...feedback?

joel

>THe shapton 12K stone has been discontinued at the factory. It has been replaced by the 15k stone. We stock lapping film down to .3 micron.

One big difference between traditional waterstones and lapping film. If you apply pressure the particles of slurry crack and you get a sharp finer abrasive.

That's the whole point of creating a slurry and then letting it dry a little before progressing to the next finer stone.

THe shapton stones don't really use the slurry concept excpecially if you use a lot of water with them.

With regular stones such as the ice bear, the king, or the Nortons. you use a slurry, and get the effect. THat's why, while we do as you mention, stock the 10K stone, we also stock it in a kit with a 1k and 4k stone. what this means is that you can jump from a 4k stone to the 10k stone and there's no real issue.

Is it worth the extra step if you already have an 8k stone. probably not. but if you have a 6k or a 4k and you want to add a finer stone why not go to 10K?

.

Re: 10,000 grit stone...feedback? *LINK*

#6

Re: 10,000 grit stone...feedback?

Lyn J. Mangiameli

>I haven't used this stone, but I do use the 12000 Shapton, .5 and .3 micron "papers" (the latter thanks to Russell Seaton), and .5 micron chromium dioxide honing compound.

There is no question in my mind that the 12000 Shapton leaves a discernably and functionally superior edge compared to the 8000 Shapton. I find this diffence to be most meaningful on the harder more "exotic" alloys such as A2 and M4. All it takes is a hand magnifier to evaluate the difference, and a dense difficult to plane wood to observe the difference in cut. I don't work with the softer woods much, but frankly, I'd expect a very sharp edge to be even more meaninful when one is trying to slice softer and more flexible cell walls.

One of the things to keep in mind is that no abrasive is uniformly graded to its advertised rating. There is always some range of particle size, either in the original distribution, or as the abrasive breaks down during use. Usually the finer grits are more closely graded, but still the range becomes apparent in the uniformity (or more precisely, the lack of uniformity) of scratch pattern that is apparent under magnification. Frankly, I am rather dissapointed in the lack of uniformity of partical size in the nominally .5 micron papers and honing sticks, but at least all of the particles are are relatively small even if some are three times the size of others.

Natural waterstones usually have a very wide range of particle size, but fortunately the particles break down in size with use, thus the reason why final polishing is done with the slurry, rather than on a newly exposed bare surface. The newer waterstones have a more durable abrasive that is less prone to fragmentation, and is less prone to build up a slurry, but there is usually much more uniformity in particle size (but still some). I find a more traditional 8000 waterstone to provide a surface more refined than an 8000 Shapton, and I find a 12000 Shapton to provide a surface only slightly better than an 8000 traditional waterstone (thus the significant difference between an 8000 and 12000 Shapton). There is no subjectivity here, all one has to do is observe the obvious difference under magnification. These differences remain aparrent on a well tuned high performance smoother. I've replicated it literally dozens of times.

Now the difference is not going to last indefinitely, as the edge will become worn sooner or later, the rate at which the difference is obscured will depend on the wood planed, the bevel angles, and the steel from which the blade is made. But again, the difference on a freshly honed blade is unequivocal in my experience. To me the moral is, find a method that will allow you to achieve and highly refined edge, and make sure that method is one you are comfortable in returning to often.

For what it's worth, I flatten all my blade backs on a 12000 Shapton stone, and hone all my flat blade edges with .5 micron papers applied to the platters of the Lee Valley Power Sharpening System. Wood is too expensive not to use the best possible edge available when forming it.

Re: 10,000 grit stone...feedback? *LINK*

#7

What does "regular" stone mean?

Pam Niedermayer - Austin, TX

>

Re: 10,000 grit stone...feedback? *LINK*

#8

Pam, I *think* he's refering to..

Christopher Fitch @ Memphis

>... a regular stone(waterstone) vs. a ceramic stone like the Shapton.

Re: 10,000 grit stone...feedback? *LINK*

#9

Re: Pam, I *think* he's refering to..

Christopher Fitch @ Memphis

>From here: Shapton Professional Series Waterstones

The professional series Shapton stones are the latest, state-of-the-art products for really fast cutting. Nominally a waterstone, the Shapton stone is created by using a hardened ceramic powder suspended in a resin binder. We say it's nominally a waterstone because there is no need to soak the stones in water-- in fact, you shouldn't soak them since that will damage the stones.

Re: 10,000 grit stone...feedback? *LINK*

#10

Re: 10,000 grit stone...feedback?

Rob Lee

>And how are you going to sharpen the 2 1/4" blade (in the new holder) you were sent today??? ;)

Obtusely yours...

Rob

Re: 10,000 grit stone...feedback? *LINK*

#11

Re: 10,000 grit stone...feedback?

Rob Lee

>Joe -

I would also add that "Ice Bear" is a house brand for one of the larger (probably best) trading companies in Japan. The stone itself is made by a large waterstone manufacturer.

The trading company owner is an excellent photographer - he does a lot of wildlife photography, and is particularly keen on polar bears...

Just a bit of "color" to add to the answers you're getting here!

Cheers -

Rob

Re: 10,000 grit stone...feedback? *LINK*

#12

Re: Pam, I *think* he's refering to..

Pam Niedermayer - Austin, TX

>To me, a "regular" stone could just as easily be a natural waterstone; but then it was lumped in with King and Norton, which are synthetic stones. That's why I asked.

Pam

Re: 10,000 grit stone...feedback? *LINK*

#13

What size magnifier for edge evaluation? *LINK*

Russell Seaton

>I've been meaning to get a magnifying glass to check the edges but have not seen one I like yet. I've only looked at real cheap ones locally. I have seen the 10, 14 and 20 power jeweler loupes in the lapidary catalogs and they look good.

Any recommendation on magnifying power? Do the ones in the link look suitable?


img

http://www.kingsleynorth.com/jewelry/gemoroloupes.html

Re: 10,000 grit stone...feedback? *LINK*

#14

No more Shapton 12,000 stone, so...

Don Thompson, Cutler Ridge, South of Miami FL

>...what are you going to do when yours runs out? Make a bigger jump to the 15k? What do you recommend?

TIA for the advice, Lyn.

Re: 10,000 grit stone...feedback? *LINK*

#15

Is that it, you really just sent it out for

Lyn J. Mangiameli

>sharpening! :-)

Re: 10,000 grit stone...feedback? *LINK*

#16

Re: What size magnifier for edge evaluation?

Lyn J. Mangiameli

>Those will work, but are not my favorite. In general, I prefer a lens that has an integral light. I haven't been able to find a source for the small lighted pair of lenses I use (which are very convenient being about 2.5 inches square and cabable of being left in a shirt pocket). I obtained mine when I used to do research at a blind rehablitation center.

A style that should work very well, is the Codington (this is from memory, so this may be wrong, it could be Edington of something). This is like a small flashlight with a lense mounted perpendicularly on the end. ENCO among others have these and often just call them flashlight magnifiers. I find a size in the 6-8 X range to be the best compromise between adequate magnification and decent depth of field (and thus insensitivity to minor movement).

Really, I've said this often, the quality of my sharpening was utterly transformed when I started using a hand magnifier to verify the quality of my sharpening at each stage.

On a personal note, thanks for the .3 micron paper. I'll get back with you later on the details of my experience with it.

Re: 10,000 grit stone...feedback? *LINK*

#17

Re: No more Shapton 12,000 stone, so...

Lyn J. Mangiameli

>Well, first I hope it will be quite a while before this one wears out.

I'm not sure. If I had the opportunity (i.e. undesignated funds and free time), I'd be interested in comparing the 15,000 to this new "Ice Bear" to my 12000. Perhaps someone else feeling flush these days might be interested.

If this new Ice Bear had not arrived on the scene, I'd probably automatically go with the 15000 Shapton, but only if I already had an 8000 stone of some variety.

Re: 10,000 grit stone...feedback? *LINK*

#18

Thanks. Found them at ENCO *LINK*

Russell Seaton

>http://www.use-enco.com/CGI/INPDFF?PMPAGE=252

This page has the flashlight magnifiers.

http://www.use-enco.com/CGI/INPDFF?PMPAGE=250

And this one has the Coddington and Hastings magnifiers.

I expect to see a 40% improvement in your sharpening now that you have 0.3 micron paper instead of just 0.5 micron.


Flashlight Magnifiers