Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Depth stop for a round? & other moulding plane Q's

Posts

Depth stop for a round? & other moulding plane Q's

#1

Depth stop for a round? & other moulding plane Q's

Christopher Fitch @ Memphis

>Some time ago I picked up a set of hollow and round extra bases for my Record 405. I got around to messing with them and making practice cuts a few days ago.

The biggest issue that jumps out with respect to their use is getting a cut that is an even depth across the work. How does one control the depth of the cut? I know in complex moulding planes, the profile contains both the stop and a fence in most cases. Yet a Round or a Hollow does have the same features. I can understand this to a point since a stop would inherently limit the depth that the plane would cut.

Also, when using a round or hollow, would it make sense to use a batten to provide a bearing surface that would allow for a straight cut?

TIA

Re: Depth stop for a round? & other moulding plane Q's

#2

Re: Depth stop for a round? & other moulding plane

Charles

>Yes, use a batten to get a straight cut and until you get enough material removed for the plane to guide itself. I use traditional wood hollows and rounds.

Never have concerned myself too much with a depth gauge. I draw the profile I'm going for on both ends of the stock and plane down to the lines with the appropriate hollow or round. Fairing by sight helps me true the profile consistently over the stock being worked.

Re: Depth stop for a round? & other moulding plane Q's

#3

Batten

jim_reed@marietta

>You will find high end H&Rs with a slight skew. The skew causes them to *ride the batten* and thus easier to use.

Re: Depth stop for a round? & other moulding plane Q's

#4

Re: Depth stop for a round? & other moulding plane

jerry schram

>you can plow a groove to the depth of the profile and it will help guide the plane also. hope this helps Jerry

Re: Depth stop for a round? & other moulding plane Q's

#5

Two thoughts...

Ted Owen, Pittsburgh

>if I understand correctly:

First, besides drawing the profile on the end of the workpiece, draw lines across the work surface. As you progress, remaining portions of the lines indicate depth and evenness well.

Second, the hollow or round plane body is shaped (or the blade is ground, but better to shape the body) such that blade edges just disappear into the body. That design feature acts as an automatic depth stop.

Once that point is reached, tilt the plane to one side or the other to cut further, then straight up again to smooth out the shape.

Best, Ted

Re: Depth stop for a round? & other moulding plane Q's

#6

Re: Depth stop for a round? & other moulding plane

Christopher Fitch @ Memphis

>Interesting idea Jerry, Michael Dunbar mentioned doing something similar in his book, except he used a custom made blade that cuts a v-shape.

Re: Depth stop for a round? & other moulding plane Q's

#7

Remember, he is using a multiplane,..

Don Thompson - South of Miami

>.. if I understand correctly. It doesn't ride on the piece the same, right?

Re: Depth stop for a round? & other moulding plane Q's

#8

Re: Remember, he is using a multiplane,..

Christopher Fitch @ Memphis

>I'll have to try to post a picture tonight so you can see what it looks like...

Last night, I smacked the living crap out of my thumb on my left hand with a deadblow hammer and it hurt hurt hurt.

Re: Depth stop for a round? & other moulding plane Q's

#9

Re: Batten v. Fence

Barry Virginia Beach

>Chris, I can't help you much with the depth stop- I just draw the outline on both ends. As to cutting straight - when I use the Stanley 45 or 55, I use the fence to keep the cut straight. The problem is that the molding must hang off the bench to allow the fence to work. Rather then affixing a batten to the molding, I just fix a batten to an old 2 x 6 that I lie on the bench ( it has a cutoff screwed to the bottom that gets captured by the vise) and the batten is set so that the molding sticks over the side of the 2x6 so that I can use the fence. I also screw a small stop to the 2x6 at one end - it works pretty well.

Re: Depth stop for a round? & other moulding plane Q's

#10

Better late than never...

Christopher Fitch @ Memphis

>Here's a series of pics of the 405 with the 6R base...

Image 1


img

Re: Depth stop for a round? & other moulding plane Q's

#11

Re: Better late than never...

Christopher Fitch @ Memphis

>#2


img

Re: Depth stop for a round? & other moulding plane Q's

#12

Re: Better late than never...

Christopher Fitch @ Memphis

>#3


img

Re: Depth stop for a round? & other moulding plane Q's

#13

Re: Better late than never...

Christopher Fitch @ Memphis

>And a stealth gloat...

The package delivery companies have been busy this past week...


img