WoodCentral Forums

Est. 1998 — 27 years of woodworking knowledge

What size glue bottles do you buy?

Posts

What size glue bottles do you buy?

#1

JL

What size glue bottles do you buy?

JL

I typically buy the 16 fl oz bottles of Titebond in II, II - dark, and III.

Today I had to throw away the remnants of a bottle of II that had gotten hidden for a while and the remnants of a bottle of III. Not too much - between 1/4 and 1/8 of a bottle each.

Should I rethink my glue purchasing behavior?

Purchase the smaller 8 fl oz bottles?

I buy the smaller bottles of hide glue as I only use it sparingly - and it does go bad before I use the entire bottle.

Re: What size glue bottles do you buy?

#2

Re: What size glue bottles do you buy?

Keith Newton

I like to work with the 8oz better than 16. I used to buy gallons to refill them, but I’ve slowed down so use 16oz to fill the smaller ones.

When I’ve got a lot that I’m trying to get glued and into the clamps within the open window of time, I squeeze out the glue, then lay the bottle on its side so I won’t have to wait for it to slowly run up to the spout when I go to use it again. I had a hard time training my builder friend that is always needing me to help him with something not to try to help by standing it up for me.

Re: What size glue bottles do you buy?

#3

Re: What size glue bottles do you buy?

Sam Force

By the gallon for me, I do mostly segmented turning and that uses a lot of glue

Re: What size glue bottles do you buy?

#4

Re: What size glue bottles do you buy?

Derek Cohen (in Perth, Australia)

JL, glues dry out through the constant and frequent use of a bottle. I only open a bottle to decant some into a Tupperware container, which can be sealed by its lid.

I find that the glue in the container lasts and lasts. The small amount seen here could last a few weeks with ease.

The glue is spread with a silicon brush. Allow to dry and the glue peels off for re-use. I also made a bunch of UHMW spreaders.


Regards from Perth

Derek

Re: What size glue bottles do you buy?

#5

Re: What size glue bottles do you buy?

Terry Quiram

I glue up LOTS of wig stand kits for my turning club. I buy 2 gallons at a time.

Re: What size glue bottles do you buy?

#6

how to reuse old bottles

Cameron

This hits close to home, I've got 5-6 old bottles that have collected as they have either run low of were forgotten during freezing weather and are now suspect, necesitating a new purchase... Do you guys clean out the smaller bottles to refill? Not sure how I would even get the old crud out of the bottle.

Re: What size glue bottles do you buy?

#7

Hot Water 


Re: What size glue bottles do you buy?

#8

Re: What size glue bottles do you buy?

Bill Howatt

I probably use little compared to a lot of you and I've had some bottles of various PVA types that were years old. If there is enough to consider checking, I make a few test joints and after 24 hrs hit them with a hammer. If they break and it is the wood that breaks rather than the joint, I use it.

Bill

Re: What size glue bottles do you buy?

#9

Re: What size glue bottles do you buy?

TomD

I just buy the titebond 1 in 32 ounce bottles that I replace at the end of the year. I might use 1/4 to half of that. I just use it for private musical instrument and furniture projects that require that kind of glue. I have a lot of other glues as well.

I find the 32 ounce size is the best value. I replace it every year in case I make an instrument to sell. Then I want fresh Titebond 1 glue because it is the only one I trust, other than LMII glue, for warranty reasons. The excess can end up in kid crafts, or if I do a large lamination project.

If you want your glue to stay fresh relatively indefinitely, give it some bloxigen/argon and dispense it like they pull liquid into a syringe, which is to say, never draw the gas. I use dose syringes for that purpose. You will thereby have a blivet of gas over the glue, and it will last and last.

Re: What size glue bottles do you buy?

#10

Re: What size glue bottles do you buy?

AZ in Colorado Springs

I get titebond extend by the gallon. I have a couple of 16 oz "dispenser" bottles for use on projects. I fill those, then decant the rest of the gallon into a variety of small bottles -- Powerade and BBQ sauce bottles mostly, all thoroughly washed out -- filled up to the top to leave the smallest possible head space. As I use glue in projects, I top off the dispenser bottles. I use a gallon in about a year and a half, so it doesn't age out.

I get the titebond extend on line. When I see it at one of the local woodworking stores, there's always a ring of cured glue around the top inside of the jug. They must sell it very often.

Re: What size glue bottles do you buy?

#11

Re: What size glue bottles do you buy?

jessecloud

I live in the high desert in New Mexico. Its very arid here, often 2 or 3 per cent humidity. So liquids dry out quickly. I try to buy whatever I think I will use in the coming year.

When I was doing lots of laminations, that was a 5 gallon bucket.

Now that I'm making small pieces with mortise and tenon and dovetails its usually something in the 8-12 oz size.

Though with the Cover-19 around and my advanced age, I'm not buying any green bananas, as the saying goes.

Thanks for reminding me that I need to buy some glue soon!

Re: What size glue bottles do you buy?

#12

Re: What size glue bottles do you buy?

Jim Hoeller

I have been using a thoroughly cleaned mustard dispenser. The small nozzle at the tip dispenses a reasonable amount of glue and when pressure is released, the glue in the tip is sucked back into the bottle. So far, the tip has not been clogged.

👍 This page answered my questions

Your vote helps other woodworkers quickly find the answers and techniques that actually work in the shop.