Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Which bandsaw tooth number and type

Posts

Which bandsaw tooth number and type

#1

ebd

Which bandsaw tooth number and type

ebd

I am making finger joint boxes by using a router to cut dados/slots into the sides for the top and bottom. Then I glue it up with the top and bottom floated in the slots. When the glue is dry I cut the box top from the bottom.

To take the thinnest kerf I want to do the cut with a bandsaw. Since the sides are 5/16" to 3/8" thick and the ends are up to 6" I'm at a loss as to which bandsaw blade might give me the best result.

A 3 or 4 tooth would be fine for the ends but too coarse for the thin walls of the sides. A very high tooth count clogs and burns when cutting the ends.

Is there a tooth count and tooth type that would work for this application?

I called woodcraft bands for advice and to order but was told he didn't sell single blades and I'd have to call back as he was busy.

Re: Which bandsaw tooth number and type

#2

Re: Which bandsaw tooth number and type

David Weaver

I'd be worried about the underside of the cut (on the thin parts) with a set 3 tooth blade and would try something like 6 or 8 tooth first. I don't think your cut is long enough to worry about heat and wander (the end cut that is, the part that's thick).

The blades will have to be sharp, though.

Re: Which bandsaw tooth number and type

#3

Re: Which bandsaw tooth number and type

John in NM

I'd go 12 tpi I think, that would give you 3 teeth engaged in the thickness. Since its just 1 blade I would get a standard or a skip tooth rather than a hook tooth. They are less aggressive having 0° hook angle, so there might be a bit less chipping. I think skip will give you less clogging/burning problems in a case like this, but I'm not sure about that compared to a standard tooth. Skip is basically a standard tooth with a tooth sized gap. How that compares to a standard pattern at the same TPI is beyond me :D

Re: Which bandsaw tooth number and type

#4

Re: Which bandsaw tooth number and type

Bill White

And tell Woodcraft that you're too busy to bother them again.

Re: Which bandsaw tooth number and type

#5

Heh...

John in NM

That's a good one to remember Bill :D

Re: Which bandsaw tooth number and type

#6

You could make a sled that holds the box at 45º

Keith Newton

to the saw table. This would get rid of the deep cut. It only needs to be a short 2 x 6 or thicker with a V cut in it.

Re: Which bandsaw tooth number and type

#7

Try a very thin blade on the TS....

Barry Irby

Even a skilsaw blade. Look at good quality 8" blades. The cut will be about as thin as a bandsaw blade.

Re: Which bandsaw tooth number and type

#8

Re: Try a very thin blade on the TS....

Jim O'Connor

I have a thin kerf 7 1/4 in. blade in my TS for cutting the thin woods for my boxes . Works well.

Re: Which bandsaw tooth number and type

#9

Re:1/16" Slot Cutter

Hank Knight

I've been using a 1/16" slot cutter on my router table to cut the tops off small boxes. The cut is easy and produces a very smooth surface. The depth and the height of the cut is limited by the diameter of the cutter and the length of the arbor's shank, so it is suitable only for smaller boxes. But if your box has sides of about 3/8" or less and the top is 3/4" or so high, take a look at using a slot cutter. I've used my table saw and my band saw for this task, but the slot cutter is by far the easiest and produces the best results.

Re: Which bandsaw tooth number and type

#10

Re:1/16" Slot Cutter

Dick Coers

Most slot cutters I've used have a horrible chip out problem. Do you climb cut or do a shallow scoring cut?

Re: Which bandsaw tooth number and type

#11

Re:1/16" Slot Cutter

Hank Knight

I've had minimal problems with chip out. I worried about that, but my first attempt was clean as a whistle. The second attempt (in walnut) I noticed a very small bit of chip out, so I slowed the feed rate and the problem went away. The rest (4, actually) have been clean as a whistle. I think the tiny 1/16" cutter is so narrow that it doesn't lift enough material to chip seriously. I try to feed with a slow, steady rate and the cuts have been clean. I've not tried climb cutting; I've not found a need to.

Re: Which bandsaw tooth number and type

#12

Re: Try a very thin blade on the TS....

William Duffield

It won't work on a SawStop, but the 8" blade Barry suggests will, with a dado brake cartridge. Another option is a Micro-Kerf 40 (0.070" kerf) from Total Saw Solutions, but be sure you are sitting down before you click on the link.

http://www.totalsawsolutions.com/page/10-in-micro-kerf-40-deep-cut-table-saw-blade

Re: Which bandsaw tooth number and type

#13

ebd

Re: You could make a sled that holds the box at 45

ebd

Won't work for a box that's 6" wide on a Delta 14" with no riser.

Re: Which bandsaw tooth number and type

#14

ebd

Re: Try a very thin blade on the TS....

ebd

HaHa. Just a wee bit pricy for me.

Re: Which bandsaw tooth number and type

#15

ebd

Re: Which bandsaw tooth number and type

ebd

Thanks. I'll look for a 12 tpi standard tooth and give it a try. I'm sure it will work much better than the very high tpi blade that I cut the last box with. The macassar ebony was denser than previous boxes and the end cuts were difficult.

Re: Which bandsaw tooth number and type

#16

Re: Try a very thin blade on the TS....

William Duffield

It sure is expensive, but it cuts very cleanly, cuts a lot deeper kerf than a Diablo and converts a lot less of your rare and expensive wood into sawdust. A SawStop is pretty expensive, too.

I've also seen a guy machine a block of Aluminum that made up the difference between the radius of a 10" blade and the radius of a Diablo, and pop rivet it to a SawStop brake shoe.

Re: Which bandsaw tooth number and type

#17

They can be even worse...

David Weaver

...stew mac makes a relatively tiny blade that cuts fret slots in guitars.

I've never used one (my dovetail saw cuts an identical size, and I wouldn't dare waste my time in the shop making jigs to use something like a table saw fretboard cutting thingy dingy).....but I've heard many people mention that they bought one...

...and proceeded to go back to buying pre-slotted fingerboards.

(for reference, the thin edge of those blades is .023", but the thin edge is not very deep - probably half an inch before the blade shoulders to a larger thickness).

Re: Which bandsaw tooth number and type

#18

At least they offer free shipping ...