Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

epoxy metal to wood

Posts

epoxy metal to wood

#1

epoxy metal to wood

Paul Blackwell

I'm building some tea candle centerpieces featured in the last issue of Wordsmith magazine. They specify using 1 1/2" dia. copper test caps to hold the candles. The big box stores didn't seem to know what they were, but I found them online and ordered them. They are wrought copper, very thin walled, .010 thickness. The plan says to screw them to the wood base with flat head screws, but I'm concerned about the thin copper distorting. Would epoxy glue hold bare copper to unfinished wood? Appreciate any comments.

Re: epoxy metal to wood

#2

I’d use E6000


Re: epoxy metal to wood

#3

Kneale Brownson

Re: epoxy metal to wood

Kneale Brownson

Maybe use a round-nosed router bit to create a nest for the copper to sit in and a countersink screw?

Re: epoxy metal to wood

#4

E6000- essential shop adhesive

Bill Tindall, E.Tn.

I have used this adhesive to glue metal to wood. My wife's cousin uses it for assembling jewelry. It seems to be able to stick anything to anything. I always have a tube of it on hand.

Re: epoxy metal to wood

#5

Re: epoxy metal to wood

William Duffield

You are planning to put lit candles in the copper cap and let them burn down, right? The temperature of the melting wax is too high to be compatible with most adhesives used for wooden projects. Epoxy and E6000 will both melt and release at that temperature, and the burning candle will fall onto your table cloth, with devastating consequences.

I haven't seen the wordsmith [sic] plans, but it makes sense that the cap would be intended to distort to conform to the shape of the screw head. If I were doing this project, I would drill a countersunk hole in the end of the wooden part, drill a pilot hole in the copper cap and use a conical punch against a soft wood substrate to deform the copper to match the shape of the screw head.

Re: epoxy metal to wood

#6

Re: epoxy metal to wood

TomD

Do these cups go into holes in the wood, if so the epoxy should be fine. It isn't likely to get so hot it will come out. I once had to heat an iron red hot to get a shaft out of a golf club, and it had to go off like a roman candle before it shifted. Don't use 5 minute. But any serious epoxy would work.

Better idea would be to get candle holding thingies from LV, and try them, people have been socketing candles in wooden sticks for ever. Easier clean up if you remove the candle before it burns down, but even if you don't, the puddle of wax will keep the epoxy cool, and when the wax is all gone, the wick will go out.

Do not attempt to surface mount cups with epoxy, that is asking too much.

http://www.leevalley.com/en/wood/page.aspx?p=32799&cat=1,250,43233 Intended for use?

http://www.leevalley.com/en/wood/page.aspx?p=45036&cat=1,250,43243,50237

Re: epoxy metal to wood

#7

Re: epoxy metal to wood

William Duffield

Without seeing the plans, my assumption was that he would be surface mounting the caps. Insetting them in a round mortise is a horse of a different feather. That should work. The only problem with your recommendation of direct mounting in wood is that some jurisdictions now require a metal insert between a candle and a wooden candlestick, because of the fire hazard. Another, perhaps less than useful, piece of information is that there are high temperature epoxies that will shrug off a candle flame. My wife used to work for a company that used them for making thermostats for hot water heaters and coffee machines, but finding one at your local Rocklear or Woodcraft isn't going to happen.

Re: epoxy metal to wood

#8

Re: epoxy metal to wood

TomD

The heat resistance goes up if you post cure. That is what happened with my golf club. I had this hot plate designed to keep coffee warm and I took to using it to speed up the cure of the golf club heads. The epoxy was shafting epoxy. Not something normally heat cured. Anyway, it took dramatic heat to get the head off. While red heat was involved, obviously that was due to difficulty in getting the the heat fully conducted, but it was vastly out of proportion with any other head removal drill I had experience of. Post cure can happen at any time, so if you have a candle and it overheats without burning up the epoxy, it may in effect post cure the epoxy. Epoxies have varying glass transition temps, and this can affect the heat resistance.