Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Resaw blade

Posts

Resaw blade

#1

Resaw blade

James Runchey

I haven't done any re-sawing in a few years and am wondering what blade to order for my Delta 14 with a 12" riser. Seems to me I used a Woodslicer in the long ago, just can't remember. Age seems to enter in to the picture. I also seem to remember 105" as the length? Is there a better blade than the Woodslicer? Not interested on a carbide blade, at my age I'd never get my monies worth.

Re: Resaw blade

#2

Re: Resaw blade

del schisler

here is the place i get my re-saw blade from they will stay sharp longer then the woodslicer blade call them i would get the 1/2" 3tpi i have the same saw as you

http://www.supercutbandsaw.com/

Re: Resaw blade

#3

Re: Resaw blade

Howard Pollack

My 14" Delta bandsaw with riser block takes a 105" blade, just as you remember.

-Howard

Re: Resaw blade

#4

Re: Resaw blade

Yonak

I can't recommend this company as their customer service is poor from my experiences. I have done business with many band saw blade suppliers. Industrial Blade has been the best and Supercut has been the worst. Strictly my opinion from my experiences .. YMMV

Re: Resaw blade

#5

WRT Carbide blades

Brian Holcombe

I think it's a misconception that they last forever, they seem to last about 2-3 months of daily use for me, less currently with so much white oak being resawed. The most time I have gone is about 6 months, sawing walnut and softwoods, white oak kills them in a hurry (in my experience).

Re: Resaw blade

#6

Re: Resaw blade

John Veerkamp

second super slicer

Re: Resaw blade

#7

Re: Resaw blade

Yonak

James, from what I remember when I had a Delta 14", the blade length was 93-1/2" so, if you had a 6" riser, that would be 105-1/2" but, with 12" of rise, it seems to me it would be closer to 117-1/2"

Re: Resaw blade

#8

Did Delta make a 12" riser block?

Gary Smyth

I have the 14", and added a 6" when purchased. Never knew about a 12" riser. Does not appear in the manual. Is it by a third party vendor? Have you a model number?

Re: Resaw blade

#9

Carbide blades don't last forever

Bruce, a MN Galoot

But they can be resharpened.

Re: Resaw blade

#10

Re: Did Delta make a 12" riser block?

John C Lucas

If he uses a 105" blade.its a 6" riser block

Re: Resaw blade

#11

Generic term maybe since you get 12" resaw cap.


Re: Resaw blade

#12

Is it possible to use two 6" blocks to make 12" ?


Re: Resaw blade

#13

Re: Carbide blades don't last forever

Brian Holcombe

CT woodmasters can not be, so far as I'm aware.

Re: Resaw blade

#14

Re: Carbide blades don't last forever

Bruce, a MN Galoot

Lenox trimasters can be. Three times, I was told. Mine has been once. The blade cost $120, so I would demand something could be resharpened for that price.

Re: Resaw blade

#15

Re: Is it possible to use two 6" blocks to make 12

Bruce, a MN Galoot

Maybe, but that would give you a depth of cut of 18" and I doubt if the rest of the machine is up to it. That sounds like a job for a woodmizer.

Re: Resaw blade

#16

Re: Carbide blades don't last forever

Brian Holcombe

I might switch, throwing away $150 blades is heartbreaking.

Re: Resaw blade

#17

Quite sure the OP...

Brian Roberts

meant a riser that results in a 12" depth of cut.

Re: Resaw blade

#18

Re: Is it possible to use two 6" blocks to make 12

Bill Houghton, Sebastopol, CA

I wish I still had the online picture of someone's modification of a Delta 14" saw with a homegrown riser that must have been 18" or more. It was a somewhat scary looking machine.