Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Avoiding snipe with lunchbox planer?

Posts

Re: Avoiding snipe with lunchbox planer?

#26

Not only did I see it, I felt it...

Denis Chenard in Ottawa

15+ years ago. Had my Delta 22-540 lunchbox planer on the floor (don't ask...), me staggering rough boards from (if my memory serves me right) a dismantled pallet. One board was just thicker than the others, and when I fed it in the planer it lifted the feed rollers just enough that the preceding board, still running through the planer, lost contact with the feed rollers, and the cutterhead grabbed it and sent it back out. On the top of my foot. Right at the first toe joints.

Based on the spacing of the cutter marks on the expelled board and the machine's specs, the board shot out of the planer at roughly 60 MPH. Painful to say the least... Nothing got broken, but I wasn't sure for a while...

Segmented feed rollers eliminate that kind of possibility...

DC

Re: Avoiding snipe with lunchbox planer?

#27

What I did...

Grant Smith

Barry,

I eventually upgraded to a larger machine due to my logs to lumber habit, but I did fix the problem:

1. I made up a piece of 1/2" MDO the width of the planer and about 4' long. I mounted the planer down to a 4' table.

2. The MDO was attached to the folding in and outfeed tables by drilling, countersinking, and tapping 4 screws as close to the planer body as possible. These were then snugged up tight. This left me with an unsupported length of MDO sticking out each end.

3. I countersunk a 1/4" and 4" long carriage bolt head in each outer corner of the MDO such that they were clear of the top ( I think I actually ground some of the curved carriage bolt head so it was flatter). Then I snugged a nut up beneath the MDO to capture the MDO. A clearance hole was drilled in the table just larger than 1/4" (before assembly) to receive each of these long carriage bolts.

4. Three more nuts were threaded on each carriage bolt. The upper two of these were locked together such that when the third nut was brought up against it, the entire table was level. This is required for thicker stock over about 5/4". Required to avoid creating parts that are hour glass shaped with the next setup. Essentially, if the stock wont bend over its 4' length, use this setup.

5. The final nut was then tightened against the table to create about a 1/8" dish in the MDO from end to end. Measure this by putting a 4' straight edge in to the planer and measuring at the planer bed. From memory it was 1/8", but it has been ten years. Somewhere in that range is the butter zone, perhaps as little as a 16th of an inch. fiddle with results here, ymmv.

6. adjust the in and outfeed table jack screws to match the curve of the MDO and provide support.

I chose MDO because I had it on hand and it is a slick, flat surface. Used it for about 3 years before upgrading the planer and selling it. The buyer had also heard of the snipe issues and was pleased to see me demonstrate how well the arrangement worked.

You should also check and adjust the locking bar, as tighter is better on that planer.

FWIW,

Grant in Iowa

Re: Avoiding snipe with lunchbox planer?

#28

Dust under thin platen, causing hump.

Keith Newton

I haven't read all the responses, so don't know if this has been pointed out, since most people just respond while leaving the Subject line unchanged.

If the bed of this planer is a thin piece of metal, dust or chips can get under it, causing it to hump up. So even if your lifting on the infeed and outfeed, there could still be an uphill slope between the top feed rollers.

Sorry if I'm being redundant, but if it helps, hope you'll let everyone know.