Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Is There Such A Tool

Posts

Is There Such A Tool

#1

Is There Such A Tool

Doug Reynolds

I am looking for a tool similar to a nail set but, with a highly polished rounded end - sort of like a ball end.

Is there such a thing and what would I call it if looking at a catalog?

I know I can take a nail set and make my own.

Thanks, Doug

Re: Is There Such A Tool

#2

Maybe ? *LINK*

Clifton C

Looks a bit small, but might be a place to start.


Ballpoint Stylus

Re: Is There Such A Tool

#3

Re: Maybe ? *LINK*

Clifton C

I remembered these just as I hit post.

36 bucks with a 25% off coupon.


Doming Block and Punch Set

Re: Is There Such A Tool

#4

Leo Cuellar

Re: Is There Such A Tool

Leo Cuellar

You might also be able to find something if you look up "chasing tools" for repoussé work.

Re: Is There Such A Tool

#5

Re: Is There Such A Tool *LINK*

Keith Newton

There are some leather tools with domed ends, but I'm not sure what the individuals are called, but here is a link to a kit


https://www.amazon.com/dp/B01MQNSPHY/ref=asc_df_B01MQNSPHY5051529/?tag=hyprod-20&creative=395033&creativeASIN=B01MQNSPHY&linkCode=df0&hvadid=198096942604&hvpos=1o9&hvnetw=g&hvrand=2908973975851511177&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint

Re: Is There Such A Tool

#6

Re: Is There Such A Tool

Gary Smyth

There is a set called a dapping set used by jewelry makers. Some are larger sets than what is shown but there is a small set available at Harbor Freight. Jewelry supplier Rio Grande has a variety of dapping sets if this is the item you are looking for. Prices vary depending on the sizes, number and forms within the set, and the metal used for the punches.

Re: Is There Such A Tool

#7

Chuck a nail set in your had drill

John C Lucas

And then take it to the grinder or disc sander and shape it any way you want. Could also be done with steel rod or broken drill bit. Could easily be heat treated if you need it hardened.

Re: Is There Such A Tool

#8

Agree...

John in NM

Repousse tools are what I thought of too. There is one that is like what the OP is looking for, though it may only be available as part of a set.

Its easy enough to make one of these out of a nailset or a pin punch. Bench grinder followed by some Dremel work sanding and polishing.

Re: Is There Such A Tool

#9

What are you making?


Re: Is There Such A Tool

#10

Re: What are you making?

Doug Reynolds

Alan Lacer's "Ostrich-skin Mesquite". Had a turning class with him last week at Marc Adams School of Woodworking and he showed the class an awl handle made of very rare West Texas Ostrich skin mesquite. I am trying to duplicate it poor man fashion.

Seems like the nail set remodel is the easiest way to go. I'll be making a few hook tools for turning so, metal work is on my To Do list anyway.

Thank you all for your suggestions. Happy Independence Day, Doug Reynolds

Re: Is There Such A Tool

#12

Ken Vaughan

Could it have been an air scaler

Ken Vaughan

Use of an air scaler with the steel tips rounded was popular about 5-10 years back. Robert Rosand still textures hollowing tool handles he sells with one of these.

With 20 or so steel needles grounded to henispherical shape hammering the surface, the texturing goes quickly.

Harbor freight sells them cheap.

Not having seen the Lacer handle, this is a guess.........

Re: Is There Such A Tool

#13

Needle scaler?

John K Jordan

I bought some pneumatic needle scalers and tried that with one.

Efficient but not much for detail work. Really fantastic for cleaning up brake and chassis parts on the truck though!

JKJ

Re: Is There Such A Tool

#14

Re: Could it have been an air scaler

John in NM

I would bet a needle scaler would be too blunt yet too aggressive for stipple texturing. I've done a lot of it with gunstocks, and build many tools to do the job. The only air tool I've heard of working well is a short stroke mason's air chisel with custom tips. Scaler's depend on some sideways flop to the needles, which is not what you want for precision stippling.

Re: Is There Such A Tool

#15

needle scaler works nicely

Dick Coers

I took out all the needles, chucked them in a cordless drill, then ground them to a spherical end. There is a flange on the needle, so you have to open the drill chuck and get the flange back behind the jaws before tightening. You turn down the compressor, and keep a very light grip on the scaler. Works great! The replacement needle packs are very cheap. I ground a set to fine points, and another set to a sharp single bevel angle on the end, and a third with a concave grind. Each provides it's unique pattern.

Re: Is There Such A Tool

#16

Ken Vaughan

Reference AAW Journal vol 20:2 page 10

Ken Vaughan

Works quite well. Bob Rosand demonstrated in Phoenix several years back.

It could simulate an ostrich like leather texture.

Re: Is There Such A Tool

#17

Re: Reference AAW Journal vol 20:2 page 10

John in NM

I was always looking for a more aggressive texture than what you are describing and the ability to stipple within very precise limits - less than 1/32". The tools I made for it worked with vibro engravers and a modified Foredom chisel.

A dialed down air chisel might do that, but it never did seem practical for what I was after - the needles have to be much more tightly held than the scalers I've worked with when welding. The whole idea with those is that the needles can wiggle a bit to knock the flux off the weld.

I would show you a picture, but they were all on photobucket.

Re: Is There Such A Tool

#18

Modified scaler

Clifton C

I cut my pins short to give a little more control. These stick about 1.5" out of the barrel. If I was to do it over, I'd probably go 2". A rubber band will corral the pins for a tighter pattern, removing some pins makes a smaller pattern and shaping with toothpicks and a rubber band gives another option.

Food for thought...

cc


Re: Is There Such A Tool

#19

Ken Vaughan

Ever try a stockmakers stippling tool?

Ken Vaughan

Brownells sells them in 12, 16, and 20 lines per inch. Used as a lower skill alternative to checkering on gunstocks. Also used by carvers to texture backgrounds.

Mallet work rather than electricity

Re: Is There Such A Tool

#20

Yes, made several...

John in NM

That is what I do with these tools.

I still use the two most successful designs. I never did try Brownell's tool because it did not look aggressive enough or random enough for the look and feel I wanted from the stippling. Looked far too slow for production work as well.

The first one I made was sharpened cut nails welded together then welded to a rod so it could be used like a hammer. It cut deeper than Brownell's design likely would and was undoubtedly faster and more convenient (no work holding jigging required because the tool can be used one handed). From there I moved on to the vibro engraver (they wear out quickly but give good results) and from there to the Foredom chisel tool.

I've stippled hundreds of grips with these tools. And the irony is that I like checkering a lot better, but for what I'm selling the market expects stippling instead (a copy of a German grip for a PSG1 rifle - originals are stippled so mine must be as well).

Re: Is There Such A Tool

#21

Re: Modified scaler

John in NM

Yeah, not aggressive enough, here's a sample of what I do:


My tools are a lot sharper than that to get the rough finish. I have a different method of holding the needles I make for them too.

For a while I was trying to sell the tool to Foredom, as an add on to their chisel handpiece, but they were not interested. It probably doesn't hit hard enough for what you are doing with those rounded needles. Mine does work well on metals though, so I may end up selling it to a friend who manufacturers tools for jewelers.

Re: Is There Such A Tool

#22

Ken Vaughan

Thank You!!


Re: Is There Such A Tool

#23

Re: Modified scaler

Clifton C

John, nice stipple, that looks really good. I think I'll try sharpening some needles and see what happens...(new sets cost ten bucks)

cc

Re: Is There Such A Tool

#24

Thanks!

John in NM

All the versions I've made got good results, the trick has been improving speed while developing something inexpensive enough to sell - at least in theory.

Best result was still with the hammer like tool, but it was obviously the slowest to use and tended to give me tennis elbow :D

I got best results sharpening points pretty acutely, then cutting slightly more bluntly angled points at the very end, usually three - four facets cut with the side of a little cut off wheel. Mine don't need that swaged end on the needles to hold them in the scaler, so I've been using regular W1 stock to make the points.

Re: Is There Such A Tool

#25

Re: Is There Such A Tool

philip f Duffy

All ship sailors know what a needle gun is and how to use it to take off paint. Perhaps one of those needles would be ideal??