Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Display Case done

Posts

Display Case done

#1

Display Case done

Bill Tindall, E.Tn.


Something for the minimalist finishers to consider. When I went to clean it up with Windex, had I finished it with shellac I likely would have dissolved the finish.

The glass bill was $300. The shelves were about $70 each. Seemed way high to me.

Re: Display Case done

#2

Like Everything

Mark Mandell - Gone Round In New Jersey

except the grain in the drawer front. Piece is so nicely balanced that the grain not being centered and/or bookmatched bothers my eye.

Re: Display Case done

#3

Re: Display Case done

Stuart Hough

Absolutely gorgeous piece, Bill.

Re: Display Case done

#4

Re: Display Case done

Virgil Johnson

Nice work.

Re: Display Case done

#5

Re: Display Case done

Thomas Skaggs, Foothills of Mount Level

Nicely done Bill. I like the choice of hardware. I like that you used a nicely figured board for the drawer font for added interest. T

Re: Display Case done

#6

Kneale Brownson

^^My thoughts too^^


Re: Display Case done

#7

that decision was not made hastily

Bill Tindall, E.Tn.

"I like that you used a nicely figured board for the drawer font for added interest. "

I had a hard time finding rift cut boards where the grain spacing was about the same. Ash grows quickly here and it is difficult to find fine textured boards. As a result I sorted through my entire stock of ash, some500+ feet to pick lumber for the main cabinet. Along the way the board the drawer came from popped out. I debated until the last minute whether to indulge the otherwise plain piece with something that was not rift. I have some curly rift cut ash but it didn't look right on the drawer.

I think a plain rift drawer front would have yielded a more elegant piece. However, I risked the indulgence of the fancy drawer front. Two of the "eyes" lined up with the pulls nicely, but the 3rd is some off center (less so than the appearance in the off axis picture). Having walked past the piece a few times now as a spectator, rather than the builder, I am growing attached to it.

Re: Display Case done

#8

Ellis Walentine

Very nice

Ellis Walentine

Thanks for documenting the build of this piece. It was a lot of work, but worth the effort.

Polished glass edges are pricey. I'm not shocked by the glass cost.

Ellis

Re: Display Case done

#9

Alan Young

That Case Should be On Display

Alan Young

"Less is More" Elegance except for the "more" parts. 8) :) Please remind me-does the top profile of the glass in the doors follow the curve? Or is it a squared off profile? I can see the plus/minus view point re: the drawer. I have found how my eye has adapted to certain details of pieces I've built where I totally forget about something I wish I had done differently and wonder instead how I ever pulled off other details....and yes about the problem if you have used a shellac for finish-Is this a poly top coat?

Classy

Re: Display Case done

#10

Re: That Case Should be On Display

Bill Tindall, E.Tn.

"me-does the top profile of the glass in the doors follow the curve?" Yes, see companion post to follow.

The finish is Target "Waterborne Urethane". Their tech person recommended it for a water white durable finish. The result looked like something finished with a thin coat of shellac, but better durability.

Re: Display Case done

#11

Re: Display Case done

Joe in a Cleveland suburb

Awesome work Mr. Tindall.

Re: Display Case done

#12

Re: Display Case done

Chuck Kettler

Love the design of the doors.

Where did you get the glass? I dealt with the outfit south of Kingsport and they seemed real reasonable even for finished edges, but that was 20+ years ago.

Re: Display Case done

#13

Simply Elegant !!!


Re: Display Case done

#14

Re: Display Case done

Fetcham

Nice piece. I particularly like that it is elegant but relatively understated. Too often people forget that dispaly cases are primarily about the contents which the cabinet should not seek to upstage. My choice whe making one was a neutral natural silk back but your dark relatively plain (walnut?) choice is a good one.

Jim

Re: Display Case done

#15

walnut back

Bill Tindall, E.Tn.

We have some cut lead glass that will go into the case. These pieces showed up best against the walnut and poorly against a light birch or ash back piece. I suspect we might have come to another conclusion if the contents were different.