Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

How would you cut this? It's rubber.

Posts

How would you cut this? It's rubber.

#1

How would you cut this? It's rubber.

Tim Greif - West of Chicago

I'm planning to get a bunch of patio pavers made out of recycled rubber for our screened in porch. Problem is, I need to trim a bunch of them down at the perimeter on two sides of the porch due to size. Manufacturer says to use a utility knife and straight edge, making multiple passes for a clean cut.

That's gonna be a royal pain since these are 16" square and 3/4" thick. Each weighs 6 lbs. I'm thinking maybe my circular saw, saber saw or table saw. These a pretty stiff. The edge butts up to the base trim on the porch, so a perfect edge may not be needed.

Any suggestions? I'll need to trim about 24 of these.


Re: How would you cut this? It's rubber.

#2

Re: How would you cut this? It's rubber.

Grant Smith

Having cut a good deal of rubber belting and similar materials, I have found two items to be especially useful.

The first is a band saw. Make sure your throat plate is NOT made of plastic, as more pressure is on the throat area than with a more rigid material. I got around that by simply feeding a 1/2" piece of MDO in to the blade until it was centered and clamped it to the table. A hand held jigsaw is a good alternative if you don't own a band saw. With either tool, uses a medium toothed blade, such as one made for rough wood cuts.

Secondly, an old electric knife was used once on some rubber about a half inch thick, and it worked very nicely. The two opposed serrated knives buzzed right through. I recall spraying the knives every ten inches or so with a light oil reduced the strain on the motor.

I would not recommend using a table saw. I believe the blade would get hot and start to melt the rubber.

Regards,

Grant in Iowa

Re: How would you cut this? It's rubber.

#3

Here's a video that may help . . .  *LINK*


Cutting Rubber Tiles

Re: How would you cut this? It's rubber.

#4

Re: How would you cut this? It's rubber.

John K Jordan

I've cut a lot of 3/4" thick rubber stall mats for my barn, also made from recycled rubber. These mats are 4'x6' and are very tough and heavy.

I use a straight edge and a sharp utility knife. There is no way the utility knife will go through the entire 3/4" in one pass so I make multiple passes. For the big stall mat it helps to bend the mat over a piece of wood at the edge to allow the blade to clear the first cut. The mats usually come out pretty straight but for the barn that's not my primary concern so I don't try very hard.

I have tried several saws and even a knife edge in a jigsaw but all were horrible since the rubber grabbed or gummed up the blades. I have not tried the bandsaw since there is no way to hold the mat on the bandsaw table without a huge aux table or about 6 people.

I wonder if a new (sharp) shear made for metal would cut the tile.

JKJ

Re: How would you cut this? It's rubber.

#5

Re: How would you cut this? It's rubber.

Keith Newton

Tim, If this is anything like cutting some of the easy to melt plastics, use a very coarse jigsaw blade, with a slow oscillation speed, and lots of forward pressure. High speed and slow feed will lead to faster melting. You might also spray a lubricant on the blade between cuts to keep it cleaner.

Re: How would you cut this? It's rubber.

#6

Re: How would you cut this? It's rubber.

Ralph Lipeles

Lots of good suggestions so far, but I will add one more. Can you remove the trim so that the tiles are beneath it rather then butted to it? That would reduce the need for very accurate trimming.

Re: How would you cut this? It's rubber.

#7

Re: How would you cut this? It's rubber.

Pete in Holland MI

Cutting rubber with a sharp knife is a challenge due to the friction of the side of the blade and the rubber. The sharp knife actually does well. It's the friction that is the killer.

Have someone or some thing flex the tile at the cut-line 5-10 degrees so the rubber will open up some when cut. It will cut remarkably easier this way.

This is true for any solid rubber material.

Re: How would you cut this? It's rubber.

#8

Wonder what the Manufacturer recommends?


Re: How would you cut this? It's rubber.

#9

Re: Wonder what the Manufacturer recommends?

John K Jordan

Tim wrote in his first post: Manufacturer says to use a utility knife and straight edge, making multiple passes for a clean cut.

JKJ

Re: How would you cut this? It's rubber.

#10

Re: Wonder what the Manufacturer recommends?

Barry Irby

Duh! You are correct sir. I forgot.

I think that would work well if you had somebody to help you and they could bend the pieces backwards to open the crack.

Re: How would you cut this? It's rubber.

#11

Re: Wonder what the Manufacturer recommends?

John K Jordan

>>>I think that would work well if you had somebody to help you and they could bend the pieces backwards to open the crack.

I mentioned above the method I use working alone (hard to find good help!): For the big stall mat it helps to bend the mat over a piece of wood at the edge to allow the blade to clear the first cut.

I've thought about using some lubricant to reduce the friction too (which is significant) but bending it over a something works so well - usually just put a 1x2 or 1x3 under the mat at the cut line.

JKJ

Re: How would you cut this? It's rubber.

#12

Thanks everybody. Test results w/ PICS

Tim Greif - West of Chicago

Thanks for the tips everyone. I decided to experiment. I used the manufacturer's recommendation, as well as Yonak's link for the saber saw method.

The far right cut is using the utility knife, along with JKJ's tip to bend the tile over a piece of 1x stock to reduce the knife blade friction and achieve a clean cut. This produced the finest cut of all.

The second (from the right) is using a coarse blade in the saber saw with the tile sandwiched between a sawhorse and a 1x piece clamped together. Used the top 1x as a saw guide. This produced a very acceptable cut for butting up against a wall, although not near as clean as the utility knife method.

The third cut (from the right) was similar to the second, but with a bit finer blade, no saw guide and pretty much freehanding the cut on a marked line. This was the worst of the three, but still probably acceptable for butting up against a wall base mold.

I'll likely use the second method for everything except at a door opening where the edge will be visible. For that, I'll use the utility knife method.

Thanks again for the suggestions. You guys are great, as always.