Barry there are too many variables here. How much time and lucre do you care to spend? Do you want full-size heirloom dressers that the kids will grow into, or kid-sized dressers that they will grow out of and pass along to their children someday? Is there a prevailing theme or style or guiding principle, other than cherry wood?
I would let your personal aesthetics dictate the form and basic look of the piece and then figure out how to make it. If you need guidance on construction, or even feedback on design, you know you'll get it here.
Last Fall I completed a large double chest of drawers for my kids. It was built to fit in an alcove in their bedroom. They asked for a utility piece; but I designed it to stand alone so if they ever moved, it could be viewed from other angles. It is built of curly maple. The sides are sort of frame and panel. The "panels" are 5/8" solid maple strips splined together and left floating in grooves in the rails. Only the top, bottom and middle ones are mortised and pinned onto the stiles to keep them from bowing. The back is a large frame and panel assembly with 3/4" poplar rails and stiles and plywood panels. The drawers are 1/2" BB ply with solid maple drawer fronts that are single boards with breadboard ends. I used Blum "Blumotion Tandem" under mount slides attached to the front stiles and the back. The case is an open frame, kept square by the joinery at the top and bottom. It works well, but it took a little "coaxing" to get it square. If I ever did it over again, I would use a solid panel for the bottom and a solid sub panel under the top for a case that large. I think that would have made the open case easier to square.
Barry, I built this simple Shaker style chest for my son when he was 10 years old. Pretty basic, but classic design that should stand the test of time ...
Ellis offers good advice. I can't keep my mouth shut though, so here's a few general ideas...
Frame and Panel is a good way to go. You can make a solid sided chests of drawers but that wood is going to move and you will have to compensate for that, which can be tricky as you will also need runners or slides that don't move.
Use false drawer fronts that screw on. They are likely to get banged up and need replacing over the years, much easier just to make new fronts and screw them on.
Route grooves on the side of the drawers and screw wood or plastic runners to the sides. Easy to fit, even if the piece isn't perfectly square and cheap to replace. Slides are expensive and not flexible to variations in the case width.
Make the back removeable for ease of assembly and repairs.
Fashion a stop mechanism for each drawer so that it can't accidentally be pulled all the way out and hurt someone.
Overbuild the sucker. A friend of mine who is a superb furniture maker mentioned once that he was rebuilding the night stand he made for his young daughter. I asked how it had failed and he said "She said she was 'kind of dancing on it.'"
Hope you will share progress often, sounds like a great project.
I did not make it clear that I made them adult sized beds and night stands and now want to make them full sized chest of drawers.
These will likely get moved around over their lifetimes so I want to make some that are tough and not too frilly so they will be easy to move without damage.
Can't predict the climate they will live in. I'm in Virginia and one of them is in Florida and the other Tennessee, so we already have a variety.
I thinking something shaker style if such a thing exists.
I know the questions were like how high is UP?, but I want to pick the collective brain here.
Thanks, I agree with most of it. Trying to make chests that will be light enough to move easily but tough enough to survive the move. And reasonably attractive.
Even a modest sized chest of drawers made from hardwood is heavy and one 50+/- inches tall is very heavy. Two people can not handily move my larger chests of drawers. If light is essential you need to make the sides frame and panel and plywood.
Barry, I can offer nearly zero experience in this area, but Bill Hylton's book "Chest of Drawers" has a number of options with NICE construction details. In fact, I consult this paperback whenever I build a single/multiple drawer end table etc. to refresh my memory on construction details. While I once bit-the-bullet on a three drawer cabinet and constructed dust covers, I would not go to that extra effort unless you really want to go the extra mile. Drawer sliders are a matter of taste. I have to admit, they are nice - but certainly not traditional and, IMHO, do not pass down that heirloom quality - if that is your intent. A lot depends on your drawer making skill and what the future holds for your chest. Do you want a possibly hard-to-open (by children) or an easy to open drawer, albeit on mechanical sliders, in the future. Do you want to improve your woodworking skills by making nice fitting drawers or not so much? Not easy questions to answer, at least for me. I think both Hank and Derek's suggestions make sense. And Bill's point regarding weight needs consideration. From what I've read, the modern generation does not like permanency. So, making a huge, heavy chest might not be workable - but who knows. I think the size of Hanks chest would be the maximum I would build so it can be moved relatively easily. Good luck. Jim
PS. The Hylton paperback has a nice description of the NK (Nordiska Kompaniet) drawer slider construction technique that I have used and it is quite nice.
Bill makes an excellent point, and I'm not arguing.
But if it does wind up to be heavy, try the link below.
I know it has a kind of "as seen on TV" feel, but they really do work.
I'm an old fart with a bad back and my wife is a wee wisp of a thing, but we have used ours to move a 5 ft - 8 drawer cherry dresser I made. Also good for sofas, etc. You can lift those with ease and it protects your back.