Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

OT - Lengthwise Saw Cut in Copper Water Pipe

Posts

OT - Lengthwise Saw Cut in Copper Water Pipe

#1

OT - Lengthwise Saw Cut in Copper Water Pipe

Don Stephan

In a 12" length of 1 1/4" or 1 1/2" copper water pipe I would like to make a single lengthwise saw cut about 6" long, leaving the 3" at each end untouched. I have cut some aluminum with a triple chip saw blade on a miter saw. Can a triple chip or other saw blade be used on the table saw for this? The pipe would be secured to a plywood carrier and of course the blade would have to be raised into the cut and then the plywood and pipe advanced a few inches. Thanks.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#2

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

Bill Tindall, E.Tn.

Copper is grabby. The risk is the pipe will seize on the blade.

How about a Dremel with a abrasive blade?

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#3

Milling machine

John K Jordan

Do you know anyone with a milling machine? A slitting saw seems perfect for this. Clamp the pipe to leave access to the side, move the saw into the pipe with the Y-axis, then down the length with X. Very controllable and can be precise.

If not familiar with slitting saws, here is one in action cutting a steel tube. Copper should be easy. https://www.youtube.com/watch?v=rVPzrB2kYhc&feature=youtu.be

Saws of various widths are available. Or if you want a wider slot and end mill would do it.

If you lived closer I could do it here.

JKJ

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#4

cutting copper

Clifton C

Don, I've cut 1 inch copper pipe, 4 foot long, on a shop made angle jig, sort of what you would use for angled table legs. (I was making copper cat tail leaves.) I ran a few lengths of blue painters tape down the pipe and on the jig, then glued the pipe to the jig with too much hot melt glue. You are not making a thru cut but I'd still consider long sleeves and face shield, the little chips are hot. I think I used 60 ATB, feed rate was fast enough so the pipe got warm, but not enough to melt the glue. Pull apart, peel off tape and done...As always, if you don't feel comfortable "stop".

cc

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#5

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

John McGaw

Can't comment on 'rip' cutting copper pipe but I have 'crosscut' it on the TS with a standard carbide blade when making a few ferrules for turning tools. It cut no differently than aluminum IIRC.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#6

"Type" tubing or Pipe?

Mark Mandell - Gone Round In New Jersey

If you're cutting type M, L, or K copper you're dealing with thin-wall stock and a fast-spinning blade may do, but if you're using real pipe with heavy walls for high pressure applications, a slow speed lubricated slot saw or milling bit in a Bridgeport is the way to go on this.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#7

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

Don Stephan

The pipe would be M, L, or K, but I like the idea of safety first. I think a friend has a mill. Thanks all.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#8

Best Option

Mark Mandell - Gone Round In New Jersey

That you know will be safe.

;)

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#9

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

John in NM

If its only one or two I would use a Foredom or Dremel tool with an abrasive cut off blade, you'd be done before you could drive over to anyone's shop to use a mill :D

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#11

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

Don Stephan

. . . if I owned one of those little rascals.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#12

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

John in NM

They tend to be worth having around, especially for the little cut off blades. I like the Foredom's better, but even those aren't bullet proof (I've worn out about 3 Dremels and one Foredom over the years - the Foredom was my own fault though).

You can usually find a Foredom CC motor with a handpiece for under $100 on ebay.

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

#13

Re: OT - Lengthwise Saw Cut in Copper Water Pipe

William Duffield

A Fein MultiMaster or one of the cheap imitations would also do the trick.