Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Making light fixture questions

Posts

Making light fixture questions

#1

Making light fixture questions

Barry Irby

I found a dodecahedron. A geometric form made of 12 pentagons formed into a "sphere". It was just a frame made of back to back angles about 3/16" on each leg. The pentagons are about 5"on a side. The form is a little bigger than a basketball. I enclosed it with some white plexiglass I had and turned it into a light fixture. It was kind of a dud. The plexi was to opaque and it did not put out much light.

My son said, "I thought you were going to do it out of wood." Duh! I have made a number of fixtures before out of stuff like birdseye maple cut very thin. Never made any that had pieces that were as large as these 5".

the questions....What wood would you use? How thin? Is there anything you can put on it to make it more translucent? How would you keep it flat? Could you glue it to clear plexi? Or laminate it between two layers. The fixture will hang from a cord.

Re: Making light fixture questions

#2

Re: Making light fixture questions

Hank Knight

Barry,

That would be an interesting project. Speaking as someone who has never done anything remotely like what you're proposing, I'm thinking light and strong for the wood, like cedar or white pine, maybe basswood. I'd make a jig to hold the pentagons flat during glue up, and I'd try epoxy. The jig should be made of something the glue won't stick to, like UHMWPE. I don't think a light fixture would get much stress and epoxy should be plenty strong to hold the joints together without any hardware. Finally, how about shoji paper? It weighs almost nothing and it should transmit enough light to make an effective light fixture. I guess what I'm really thinking about here is a Japanese lantern.

My $.02.

Hank

Re: Making light fixture questions

#3

Re: P.S. *LINK*

Hank Knight

Thanks to Bucky Fuller, you can make a geodesic dome or sphere out of triangles, which might simplify the project a little bit. Google "geodesic sphere" for lots of photos and ideas. Here's an interesting link from that search:


Making a Geodesic Sphere

Re: Making light fixture questions

#4

Re: Making light fixture questions

Barry Irby

Thanks Hank...I don't have to build the dodecahedron...its a skeleton made of very small angle iron. The shoji paper might be a good idea. Except I flashed on the wood idea. Being a woodworker it seemed like the right thing to do.

Re: Making light fixture questions

#5

Re: P.S.

Barry Irby

I was typing while you were posting your PS. As I mentioned in the other response, I don't have to build the sphere. I found it. Tiny angle irons, back to back, so the pentagons insert from the inside. The frame is black and right now the pentagons are starke white. I need a redesign. This is just a fun project.

I know about Geodesic domes and Fuller. When I was in school we built a few as houses. Seemed like a great idea but there were lots of problems.

Re: Making light fixture questions

#6

Re: Making light fixture questions

Dick Coers

Acrylic moves more than wood, so gluing wood to it would likely fail. End grain red oak will give you pin holes of light through the open pores. You'd have to do a lamination of parts to get the size you need. Some arts and crafts lamps used wooden shades, but often had scroll saw cut outs. They used pine cone silhottes and other natural objects.

Re: Making light fixture questions

#7

I thought of....

Barry Irby

using clear acrylic in some of them. Maybe the bottom one. I think I am going to put this up in my foyer and that would let the light shine straight down.

Re: Making light fixture questions

#8

Not wood but alternatives

Gary Smyth

I like the idea of the shadows created by the structure on the adjacent walls. Might not be effective in a foyer unless you want to create some effect. Photos are not all domes but you get the idea. Paper is wood--sort of, but here are several other ideas plucked from the web. Stained glass, frosted glass, glass globe within framework, paper, wire or thread, punched metal as in radiator covers or pie safes. Lots of cutting and fitting, but why not experiment? Pick one or several and test.


Re: Making light fixture questions

#9

Re: P.S.

Hank Knight

Barry,

Sorry for being dense. I reread your original post and understand now. Thanks for the clarification.

As a point of interest, Fuller was the baccalaureate speaker at my college graduation - a very long time ago.

Hank

Re: Making light fixture questions

#10

One thing that comes to mind,

Keith Newton

Is rich pine, which is naturally translucent. If you could cut it thin so it is end-grain, it would glow amber. Of course, if there was ever a spark, it would probably burn about as fast as paper soaked in paint thinner.

I've brought home some found rich pine burls that I thought I would do hollow turnings out of, but then someone might get them and think its a good idea to put a candle inside. This is the only wood that I can think of which you could just lay a lit match on top of that would be enough for ignition.

Re: Making light fixture questions

#11

Re: One thing that comes to mind,

Barry Irby

My grandfather collected it when he found it. Called it "lighta" wood. He had tended fires for his whole life, curing tobacco and heating his house with a fireplaces. He would split off a little piece to light the kindling.

You are right, almost too flammable to have around.

Re: Making light fixture questions

#12

Re: One thing that comes to mind,

William Duffield

Is "rich pine" the same thing as "lighter knots" or "fat wood," which I think is highly resinous southern yellow pine, mostly found in the base of the tree and tap root. Since SYP doesn't grow around here, my wife buys it from L.L.Bean.

Re: Making light fixture questions

#13

Re: One thing that comes to mind,

Keith Newton

It isn't just in the roots, it can be all the way up the heart, and especially at the branches.

I think when the tops of large trees are left to decay, some of the volatiles slowly escape, but leave other resins that concentrate in what remains. That becomes very resistant to decay.

Down here in pine country it's all over the place unless they burn the remains after logging.

Re: Making light fixture questions

#14

Re: Making light fixture questions

Don Orr

There are some woodturners that make lampshades out of very thin Aspen logs-often somewhat spalted with some interesting streaking. I believe they saturate them with an oil like "Danish" oil or similar. Norfolk Island Pine is often turned thin and saturated with oil to become very translucent. I think any light colored wood made thin enough and oil-saturated would be translucent.

Re: Making light fixture questions

#15

Re: Making light fixture questions *LINKS*

William Duffield

Google easily found this MarthaStuart video explaining the process for covering a wire frame lampshade with paper backed veneer.

http://www.marthastewart.com/919596/martha-stewart-makes-veneer-lampshade

Using the same process and with a little more care, you should be able to get a more transparent shade using unbacked veneer.

I don't know how old the video is, but Constantine's closed their Brooklyn store back in the '90s.

http://www.constantines.com

I still have some veneers from their Sunrise, FL store in my archives. Your Woodcraft in Glen Allen should carry a good selection of backed and unbacked veneers from Sauer's.

http://sveneers.com

Martha uses a tool called a bone folder, which isn't spoken of very often here on WoodCentral.

https://en.wikipedia.org/wiki/Bone_folder

If you don't have a Tapirus bairdii femur, you could make one from boxwood or dogwood.

Re: Making light fixture questions

#16

Re: Making light fixture questions *LINKS*

Barry Irby

Thanks

I have a roll of paper backed red Oak veneer somebody gave me in return for letting them use my veneer back and pump. I will give it a look.

I was thinking of cutting the veneer myself, but it might be easier to use some existing stuff. I will also check out Woodcraft's stash.

Re: Making light fixture questions

#17

Re: Making light fixture questions *LINKS*

William Duffield

It probably goes without saying that choosing a lightly pigmented wood, thinner veneer, and using an oil finish that completely penetrates the veneer and the paper backing will allow more efficient transfer of light through the shade. Ebony, e.g., would not be my first choice. You wouldn't want Jimmy Stewart (or Martha Stewart) to see your light and describe it as a "dark." :)