Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

picture frame made of rattan cane

Posts

picture frame made of rattan cane

#1

picture frame made of rattan cane

E.

Hi, I am wondering whether it is possible to make a picture frame of rattan cane.

My wife keeps painting and the frames available in our town don't do the pictures justice.

I am a novice at woodworking. I was thinking to somehow make a rabbet along the cane and then cut it using a miter saw and glue the 4 pieces together. The rabbet would be for fitting in the glass and picture.

Would this work? I haven't found a single example of this kind of frame on google.

I have a dremel 4000 and would like to get a miter box w.saw and possibly a dremel router table for routing the rabbet plus a rabbet router bit. Would it be possible with a setup like this? The rattan cane I am thinking to use is about 1inch thick.

Thanks very much!

E.

Re: picture frame made of rattan cane

#2

Rattan can be used in many ways.

Gary Smyth

Shown are two pictures made of knife cut rattan. These are from the Philippines. For these the cane was wet, split and glued. They did bamboo the same way. Culms made from bamboo made a wider border. Consistency of width was done by pulling the split material between two sharp blades. That is a art unto itself to prevent skewering oneself with the offshoots. Anyway I'm sure it can be done but might be labor intensive. The third picture is hardwood fake bamboo, gilded, available at frame shops and probably online in foot lengths.



The last picture is a wrapped/woven commercial frame. Available online.

As for the Dremel. I'm not sure that that is the right tool. Perhaps others can provide more help. By the way the "bamboo" picture is glassed in, the rattan is exposed.

Re: picture frame made of rattan cane

#3

Re: picture frame made of rattan cane

Dick Coers

I've never seen cane thick enough to rabbet. Or maybe I don't understand what you want to do. I'm thinking woven cane, maybe inlaid in a walnut frame?

Re: picture frame made of rattan cane

#4

Re: picture frame made of rattan cane

E.

Thanks Gary and Dick! I am thinking of making the picture frame from the material used in the chair photo below - the cane or sticks that come from a rattan plant.

I put together a rough image of how I thought to do the rabbet. Probably not all the way to the center of the stick.



I guess I would need to first cut the 4 pieces (45 degree cuts) and then rabbet each one. If I first do the rabbet and then cut, the rabbet will end up on the outside of two of the pieces.

Does this make sense? Could I do the rabbeting with a dremel attached to the dremel router table?

Thanks very much!

P.S. This is the dremel router table they sell:


Re: picture frame made of rattan cane

#5

Re: picture frame made of rattan cane

Barry Irby

While I think what you want to do is possible it won't be easy.

Rattan is a vine if I am not mistaken. Where it grows, it grows like a weed. They cut it and bend it into curved parts for chairs and such. The parts they make straight are not as truly straight as the name suggests. The size is not as consistent as you might think. Plus or minus a 1/16" or two does not matter in that style of furniture.

Also, I don't think the dremel is powerful enough to do the job. My experience with several Dremels suggests they will not do anything nearly that large at anywhere near the speed to make it satisfactory.

And the canes will not "index" off the tiny fence and produce a straight rabbet.

If I were to attempt this I would want to make a jig that would hold the can securely and provide some straight surfaces for either running it on a table saw or using a router. IF I could make that work, then I would miter the ends, using some sort of jig or block to index the rabbets.

Or you could assemble the canes into the frame and then rabbet them with a router. This strikes me as the best idea. Assuming you could fasten the corners in such a way as to not ruin the router bit.

All that said, I would not choose rattan for this project.

Re: picture frame made of rattan cane

#6

Re: picture frame made of rattan cane

Dick Coers

You'll even need a fixture to orient the round to get the miter on the second cut to be in alignment with the first cut. Your assumption of having the rabbet on the outside only applies if you don't second cut the miter to keep the rabbet on the inside. Working with round stock is very difficult. Agree with Barry, the Dremel is not the best tool for the job. Not saying it can't be done, but with the small shanks, cutting will be slow an noisy.

Re: picture frame made of rattan cane

#7

Re: picture frame made of rattan cane

E.

Barry, Dick, Gary thank you for your replies and sharing your expertise. I can see your points.

Glad to have got some clarity on what would be involved. I think I'll let go of the rattan frame idea for now.

Re: picture frame made of rattan cane

#8

Re: picture frame made of rattan cane

Barry Irby

I think you would have better luck making frames out of straight pieces of wood.

You could make a slender frame out of flat stock and then rip some cane or rattan and apply it to the wood.