Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Glueing Cherry observation.

Posts

Glueing Cherry observation.

#1

Glueing Cherry observation.

Barry Irby

I have been using up some cherry scraps, making them into cutting boards. I sort them out and clean them up. Some have been laying around for a year or more. I usually cut them to strips, plane them as necessary and laminate them into cutting boards about 1 1/2" thick. Some had never been dressed. I usually sand them on a big belt sander to remove any ribs left by tiny notches in the planer blades. Today I forgot the sanding step until I had applied glue to the first strip. I quickly sanded the others and glued up the board. An hour plus later when I took the clamps off the first strip fell off. I am convinced I failed to sand the oxidization off the first strip. I cleaned it up, sanded it and the matching face on the board and reglued it. We will see if it sticks this time.

Anyone else have experience trying to glue oxidized Cherry?

Re: Glueing Cherry observation.

#2

Re: Glueing Cherry observation.

Mark Mandell - Gone Round In New Jersey

Color of the tanins should make no difference in adhesion. You must have had some kind of coating or contamination on the board surface that got removed by sanding to a fresh surface. I've glued up "darkened" cherry any number of times with no issues.

Re: Glueing Cherry observation.

#3

Re: Glueing Cherry observation.

Lee Schierer - McKean, PA

I've edge glued cherry that has sat for several month to several years with no problems. There must be something else going on.

Lee

Re: Glueing Cherry observation.

#4

Re: Glueing Cherry observation.

Barry Irby

Now I am wondering. I have sprayed several things in the shop. Wonder if enough over spray settled on this piece to upset the glue? Seems unlikely, but something did.

Re: Glueing Cherry observation.

#5

Re: Glueing Cherry observation.

Keith Newton

Barry, Without seeing, it may be hard to access the problem, but since you mentioned ribs from the dull knife, it may be due to compression / burnishing of the surface from a worn down edge.

As far as sanding goes, the only glue that I would consider this to be good, would be for epoxy which purely relies on a mechanical surface texture to adhere. For the rest, I thought it was well established that nothing beats well mated surfaces produced with sharp blades.

Re: Glueing Cherry observation.

#6

Foolishly......

Barry Irby

the last time I sharpened the planer knives I did not quite get all the little notches out of the blades. My frugal streak kicked in along with my lazy gene. So the knives are sharper than would appear but still have a few grooves. Does not matter much when dressing the typical face that will get sanded later. I used Titebond III for the glue. When I re-glued the piece It seems to have worked fine.

Re: Glueing Cherry observation.

#7

Maybe it was the glue...

jesse cloud

Could it have been the glue? I have noticed lately that TBIII needs a good shaking before use or the first few squeezes will be watery.

Re: Glueing Cherry observation.

#8

Think we have a winner....

Barry Irby

or is it a loser?

This was a new bottle of TBIII. Got it at Lowes for this purpose. Its been awhile since I used TBIII and I forgot it tends to separate. It also did not occur to me it might have been sitting on the shelf a while and was not quite as factory fresh as I imagined. Wonder how old it really was? When I stirred it, it was watery on the top and thin and there was a pretty good bugger in the bottom. Is there a date code on the bottle? I see some markings, but no obvious date.

Re: Glueing Cherry observation.

#9

Re: Think we have a winner....

Steve jenkins

Just google franklin titebond date code.