Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Sloping cutting board question...Bill Tindall?

Posts

Sloping cutting board question...Bill Tindall?

#1

Sloping cutting board question...Bill Tindall?

Barry Irby

Bill, Didn't you make a round cutting board that was turned on an angle to create a sloping surface and a rim on one side? So the juices would drain to that side. Who ever did it, do you like it? Does it get much use?

Re: Sloping cutting board question...Bill Tindall?

#2

Re: Sloping cutting board question...Bill Tindall?

Yonak

I have an idea using a wide jointer and another using pre-cut strips and some tedious, and possibly fraught, belt sanding .. otherwise, how would one go about making a sloping cutting board ?

Re: Sloping cutting board question...Bill Tindall?

#3

Actually quite easily

Bill Tindall, E.Tn.

search the archives for where I described the process

Re: Sloping cutting board question...Bill Tindall?

#4

yes, we use it almost daily

Bill Tindall, E.Tn.

It has two advantages. For juicy stuff the juice has a large place to gather. But as handy, for cutting up vegies, like a bunch of onion dices, they have a place to gather too. The board was so handy that we have both a large and small version and I have made them for children. See somewhere in archives for how I made them. Actually quite easy with a router sled.

Re: Sloping cutting board question...Bill Tindall?

#5

Re: yes, we use it almost daily

William Duffield

I haven't built one yet, but am quite tempted, because I know they would also be very useful for chopping nuts, which have a tendency to fly all over the counter top, into the sink and onto the floor. The lower front lip of the board also facilitates clearance for the handle of the knife, and the bottom could be contoured to fit the curve of your favorite French chef's knife.

Another shaping method is to use a lathe, with a slanted face plate. I'm q bit curious why you didn't make yours that way, Bill. (Or maybe you did, and I just don't remember.)

Re: Sloping cutting board question...Bill Tindall?

#6

Re: Actually quite easily

Yonak

Sorry, couldn't find it, Bill. ..But I did try (maybe I don't know how to use the search mechanism). Does it have something to do with making a special sled for the planer ?

Re: Sloping cutting board question...Bill Tindall?

#7

search: carving board tindall

Bill Tindall, E.Tn.

posted 1/18/2016 I don't know how to link to it.

Re: Sloping cutting board question...Bill Tindall?

#8

Coming up empty.

Gary Smyth

I remember you writing about this but failed to find the article. Did key word on "cutting boards", Barry's name, your name. Checked out "finishes" for a year ,"furniture" for a year. WoodCentral archives from 10/16 back to 2014 articles to no avail. I'm thinking that you responded to someone else post. Replies aren't separated out. Have you a recollection of the month and date?

Re: Sloping cutting board question...Bill Tindall?

#9

FOUND IT.

Gary Smyth

Go to messages. At top of page in the banner (blue color). find "Messages Archives". Click that and list appears. Click on the first "Messages Archives" centered, the undated one.

Scroll down to date 1/18/16.

Click Bill Tindell -- Cutting Boards-- link message will pop up.

Re: Sloping cutting board question...Bill Tindall?

#10

Re: search: carving board tindall

Barry Irby

Thanks Bill. I looked it up. Nice piece of work. Especially glad to know you actually use it. I like to make stuff like this for people IF its actually useful.

Know I am over thinking it. Would it be possible to make one that is tapered on both sides? Or make one flat on one side and tilted on the other?

Now to decide if I am going to cut up the table tops or glue up some scraps.

Re: Sloping cutting board question...Bill Tindall?

#11

Re: The Link

William Duffield

Here is the link.

http://www.woodcentral.com/woodworking/forum/archives.pl?pro=search;pmd=sread;srchid=8372g753nONiQYhRux1491168026;spage=1;sanc=496009;sbid=1001;md=read;id=496009#m_496009

And, Bill did suggest that it could be made on a big lathe!

Re: Sloping cutting board question...Bill Tindall?

#12

Re: The Link

Barry Irby

I looked at Bill's method and that will work, but I think I am going to do mine on the lathe. I was just sitting hear figuring out if I could do a two sided one. I Can. Now I'm ciphering on which would be better.

I looked on E-Bay and was stunned at what some people have gotten for cut offs. What looks like a live edge piece about 8 by 12 is selling for $35. And that is in the sold listings.