Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

For anyone making a bed.....

Posts

For anyone making a bed.....

#1

For anyone making a bed.....

Barry Irby

I recently made beds for my granddaughters. Years ago I made one for my son.

On my son's bed I came up with a complicated way to install a captive bolt in the rail with a magnet to keep it retracted during shipping. I took 3/4" steel rod and cut two inch pieces and Drilled and tapped them making homemade barrel bolts as Dick mentions below in another thread. This was complicated and I may be guilty of over thinking it.

This time I went to Fastenal and found that they have Square Nuts. These are not the old fashioned ones. These are 1 3/16" square and 5/16" thick with a threaded 3/8" hole for a regular bolt.

I mortised the rails into the legs. End drilled the rails for the bolts, drilled holes though the legs and counter bored the holes to recess the heads of the bolts. Then I routed a cross slot for my newly found square nuts. Insert the nut into the slot, assemble the rail to the leg, Insert the bolt and tighten it up.

With a washer under the ahead of the bolt and against the rather large area of these square Nuts its a really solid connection without crushing wood fibers.

You can buy brass covers for the holes. I made little wooden caps with an embedded magnet for mine.

These are Fastenal 49464 3/8" square nuts. 1/2" ones are also available. I paid $2.08 each. I have no affiliation with Fastenal. Just thought this might be easy and useful for some of you and easier than making your own barrel bolts.

Re: For anyone making a bed.....

#2

Adam of Oakland

Re: For anyone making a bed.....

Adam of Oakland

I wish I had known about these nuts 2 weeks ago :)

As it stands I have small conventional square bolts that I'd thought to use for my bed rails...but there's just not enough bearing surface for them. I'm reconsidering just opening up the bearing surface with a large washer having one side ground flat and then using this to interface the mortise wall.

Given my life timing i can't order the large nuts since this has to be done this weekend. Next time...

Anyway, thanks for the tip.

Re: For anyone making a bed.....

#3

Re: For anyone making a bed.....

Michael van pelt

Thank-you for the great tip!

Re: For anyone making a bed.....

#4

Bed Bolts.....

Bill Tindall, E.Tn.

Hardware companies serving the Period Furniture trade sell traditional bed bolts. Not cheap though. There is even a neat wrench, if you want to keep traditional.

Re: For anyone making a bed.....

#5

Re: For anyone making a bed.....

Barry Irby

I had the same delima. I did not want to weaken the rail but wanted something easy to use and strong and permanent. I considered washers and even finder washers with a side or sides ground off them. I considered making rectangular washers. Thought about giant barrel nuts even if I had to make them.

I strongly considered just buying the traditional ones Bill mentions below. The cost and the necessity of keeping up with the special wrench deterred me.

In this case they only need a socket to put the bed together. I have scrounged up a socket and ratchet to go with each bed and hopefully that will solve that problem, but if it gets lost getting a replacement should not be a problem.

I am using 3/8 bolts and to get a little margine I bought the class 8 version.

Sorry I did not post sooner for you.

Re: For anyone making a bed.....

#6

Re: Bed Bolts.....

Barry Irby

Bill you are right. When I built the beds I looked at those, but the $8 each price tag at Rockler plus $19 for the wrench put me off. Thats over $50 per bed without the covers that ranged from $6 to $9 each.

However, today when I went back to look again I see they have sets of 8 for about $27 that include a 13/16" cross bolt and they have hex heads. I probably would have gone for that. Still a little worried about the consumer losing the cross bolt or barrel nut / but I have already dreamed up a way to make them captive.

What do you think of the cross bolts or barrel nuts? would there be any tendency for them to split the rail like a wedge if you really tightened them?

Re: For anyone making a bed.....

#8

Now you tell me


Re: For anyone making a bed.....

#9

Haven't you done farm work

Bill Tindall, E.Tn.

Farm nuts are often square. That is why 12 point sockets were invented. You will be able to find a 12 point that fits the square head of the bed bolt.

Re: For anyone making a bed.....

#10

What I got out of growing up on a farm....

Barry Irby

was I learned I did not want to be a farmer. I left there about 50 years ago and never looked back.

I remember when I was about 13 I got a large socket set for Christmas. Something like the 156 pc set from Craftsman. I kept it until about New Years day and then my Dad moved it not the Farm Shop. I did not have a key. The next time I saw it it was severely depleted.

I had forgotten 12 pt sockets.