Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Sawing veneer questions

Posts

Sawing veneer questions

#1

Sawing veneer questions

Joe in a Cleveland suburb

I am trying to make some veneer from walnut. I only need a couple pieces that are about 3" wide by 17" long. The thickness I am shooting for is about 3/32". The walnut has only a small amount of figure to it.

So that you know what I am working with - I have a Jet 14" BS (with riser block) and a Wood Slicer blade. It has the stock guides. The fence is broken (has been for years) and I just clamp it in place - not ideal for precision. I use the BS mostly for ripping instead of the cabinet saw.

I've been doing a lot of test trying to get a decent set up. I decided last night I'll use a straight flat board clamped down as a fence instead of the broken Jet fence. I will need to get drift dialed in and make sure my board/fence is square to the table.

Questions:

1.) Should the veneer piece be between the blade and fence so that each piece is consistent in thickness?

2.) Is it reasonable for me to think I can make veneer this thin with my setup, or should I go maybe 1/8" and plane it down by hand?

I did try cutting thicker, attaching it to a piece of plywood with double sided tape and sending it through the planer. Didn't work so well.... shattered into pieces.

Thanks!

Re: Sawing veneer questions

#2

Re: Sawing veneer questions

Bill Tindall, E.Tn.

Questions:

1.) Should the veneer piece be between the blade and fence so that each piece is consistent in thickness? Yes. Must hold and feed securely and steadily.

2.) Is it reasonable for me to think I can make veneer this thin with my setup, yes, or even thinner.

. Didn't work so well.... shattered into pieces. ...been there and done that. A drum sander is nice for veneer.

Re: Sawing veneer questions

#3

Jim DeLaney, Austintown, Ohio

Re: Sawing veneer questions

Jim DeLaney, Austintown, Ohio

1.) Should the veneer piece be between the blade and fence so that each piece is consistent in thickness?


Yes, it should. Make the fence high enough to support the full width of the veneer stock, and be sure to align the fence so that it compensates for any drift. I've successfully cut 1/16" veneers with a setup like that.

2.) Is it reasonable for me to think I can make veneer this thin with my setup, or should I go maybe 1/8" and plane it down by hand?

See above... The woodslicer blade will give a pretty decent face, but it'll still need some sanding or hand planing. Run the veneer stock over the jointer between slices to give one good surface prior to cutting.

Re: Sawing veneer questions

#4

Re: Sawing veneer questions

Barry Irby

I agree with all of the above. I have cut several hundred square feet of veneer with my Delta bandsaw with riser.

I start with a fresh blade. Use a scrap of similar wood to determine and compensate for the drift angle.

Bill is right. This is a great job for a drum sander like a Performax. Double stick tape the leading edge to a nice flat piece (sled) and run it through.

Or run one face over the jointer, saw, joint, saw, etc. Glue the jointed side down and sand the sawed face.

Re: Sawing veneer questions

#5

Thanks. I know I am on the right track now.


Re: Sawing veneer questions

#6

Re: Sawing veneer questions

Jim Dillon

Joe, by now you have completed your project and found, hopefully, that it was very doable. Here is a pic of a fixture used to apply pressure against the side of the board. It is simply 1/8 inch MDF (or similar) glued to a piece of pine attached to a small platform allowing attachment to the BS table. You could jury-rig something like this. Make sure to watch where your fingers and thumbs are as you exit the resawing as it is easy to forget in all the excitement of getting that perfect piece of veneer.

I don't recognize the guy in the picture but he had a LOT more hair then! Resawing jatoba in this case.


Re: Sawing veneer questions

#7

Re: Sawing veneer questions

Denny

Great idea. Thanks for posting the photo.

Re: Sawing veneer questions

#8

You're welcome.  Glad it helped!


Re: Sawing veneer questions

#9

At 3" wide, you can use the table saw

Dick Coers

There is more waste at the saw, but with the right blade it will come off nice enough to glue down as is.