Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

West System Pot Live VS Working Time

Posts

West System Pot Live VS Working Time

#1

West System Pot Live VS Working Time

Stuart Johnson

Pot life (100g at 72°F)

20 to 25 minutes

Working time, thin film*

90 to 110 minutes

West system 105/206 shows the above pot and working life. Does that mean you apply it for 20 - 25 minutes after mixing but the pieces around for 90 - 110 minutes.

I will be doing what for me is a complicated glue up and if the 20 - 25 minutes is the time to apply I will probably need to go to the 209 hardener with almost double the time.

Re: West System Pot Live VS Working Time

#2

All About Temperature

Mark Mandell - Gone Round In New Jersey

"In the Pot", where you mixed it, the resin will be reacting with the hardener, generating heat from the chemical reaction, and thus speeding up the set time. When you spread it out as a coating on the parts, the surface area is greatly expanded so it can radiate the reaction heat away and thus set slower. You can retard the reaction and extend the "pot life" by chilling* the resin so it warms when spread thin and exposed to room temperature, or you can put your mix bowl on a bed of ice chips (in a 2nd bowl) to retard the mix pot reaction and give you more time to work.

*Chilling the resin may not be a great idea if you are in a humid area as condensation may form on the liquid and cause issues. I've done both and prefer the ice method.

Re: West System Pot Live VS Working Time

#3

Re: All About Temperature

Bruce, a MN Galoot

I was once applying fiberglass to my canoe, right at the end of the pot life, maybe 15, possibly 20, minutes into the operation. The day was warm. My paper cup of resin started to get warm in my hand, and by the time I walked to the other end of my canoe it had completely hardened.

Re: West System Pot Live VS Working Time

#4

Re: West System Pot Live VS Working Time

Keith Newton

It has been a long time since I used the West brand, but dept of the container is your enemy, so either pour it into a shallow dish so it can dissipate the heat.

When I'm doing large complex glue ups, I prefer to mix multiple smaller batches.

Unless they have changed the viscosity since I last used that brand, I hope you have some silica to thicken it. If it is too thin , due to the slow kick time, it will drain out of any vertical joints. Not only will additives thicken it to keep it in there, it will make it better by being less brittle.

Re: West System Pot Live VS Working Time

#5

Warmth

Mark Mandell - Gone Round In New Jersey

When working epoxy (or any reactive resin product) heat is your enemy. Epoxy companies make various hardeners (fast, medium, slow) for this very reason. Heat not only makes the mix set faster it also tends to make the resin thin out leading to runs and sags on hand lay-ups on sloped surfaces.

Re: West System Pot Live VS Working Time

#6

Re: West System Pot Live VS Working Time *LINK*

Jerry Gibbs

West has a wealth of tech info on their website.


http://westsystem.com/ss/

Re: West System Pot Live VS Working Time

#7

Re: West System Pot Live VS Working Time

William Duffield

To extend the pot life, it helps somewhat to continue stirring the pot while you are applying it. This moves the heat to the outside of the pot where it can dissipate more quickly.

Re: West System Pot Live VS Working Time

#8

Re: West System Pot Live VS Working Time

TomD

I find the west slow to be slow setting. I have used tons of the stuff. Plus unlike white glue, it will ease joint fitting like a grease, and closing joints will be easy, right up to the time it goes off. I do almost everything with west with 105 205. But I don't do delicate intricate, extensive glue ups with it. Actually, life might be easier if I did. I do them with white glue and it grabs at inopportune times.

All the mentioned advice, small batches, shallow trays, adding colloidal silica has been good. I would never cool it unless I was in texas. Though, once I almost set a boat on fire when I did a large stem composite structure and the heat got so great it was ready to go on fire. Compressed air cooled it out. In that case I had a mass of it and a vertical section that impeded heat dissipation.

The number one rule to make anything go better is to do a sample. Let's say you were going to do something involving 20 M&T joints. Drill 20 holes, insert 20 dowels. Whatever. Get some base experience before trusting hours of hand work to an assembly involving an unknown glue.

Epoxy is expensive. So when I do some big task, I have a list of things around the house, from say door panels on an old truck, stonework, or boats that need some TLC. So when I have surplus material I always have a place to put it. This also stops me pushing glue, though I know better about that after 37 years of using WEST.

Re: West System Pot Live VS Working Time

#9

Re: West System Pot Live VS Working Time

TomD

"Not only will additives thicken it to keep it in there, it will make it better by being less brittle."

+1 on silica. Just to say, because there is this myth about WEST being brittle, WEST is the perfect hardness for just about anything. They got in first, and other formulators were left with the cheaper softer song to sing. Plus, by the rule of mixtures I don't think adding rock to the mix makes it less brittle. In engineering terms brittle is when something absorbs little energy prior to fracture. WEST excels at dealing with energy applied to high performing structures. Either way adding silica is a great suggestion.

Re: West System Pot Live VS Working Time

#10

control temp with shape of bucket

Robin Corell in Atascadero

With epoxy I always mix in one container and then pour it into another container and apply it from that one. I use a much larger diameter container for applying than for mixing. The mixing in one and applying from a second is to avoid using any unmixed product from the bottom corners. The larger diameter container is to avoid heat build up and shortening the pot life. My local hardware store used to sell these large shallow plastic buckets that were great for resin and epoxy work. For small amounts solo makes a small paper cup with oz, ml, and drams marked on the side.

Re: West System Pot Live VS Working Time

#11

Re: control temp with shape of bucket

John K Jordan

>>>With epoxy I always mix in one container and then pour it into another container and apply it from that one. I use a much larger diameter container for applying than for mixing.


What a great idea! I'm always concerned about thermal runaway after experiencing the mass of epoxy get hot, smoke, turn brown harden and crack.

I can't wait to tell my epoxy maniac friend - this makes so much sense I can't believe neither of us thought of it. Thanks!

JKJ