Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Hand tools help machine tools

Posts

Hand tools help machine tools

#1

Hand tools help machine tools

Bill Tindall, E.Tn.


As I band saw cut the profile for these parts for the top of the display cabinet door I realized I was splitting the line defining the profile. I hadn't thought about it. It just came naturally. I didn't used to be able to do that, not because I couldn't, but because it never occurred to me to try.

Splitting lines with a hand saw is an essential skill for hand sawing dovetails, tenons and the like. If it can be done with a hand saw, no reason it can't be done with a band saw, apparently. I had always band sawed outside the line and sanded to it. Never occurred to me before that one might just be careful and split the line to begin with. Saves a lot of clean up later. It is of some comfort that the hours I have spent learning to accurately cut dovetails is paying off with machines.

And BTW, one can chisel and carve with the spinning bit of a router under good lighting and with some care.

Re: Hand tools help machine tools

#2

Re: Hand tools help machine tools

TomD

I remember doing a demo at an LV seminar that included cutting out some 2" wood with a bandsaw. I was trying to hold the line, because in the particular case, the grippyness of the rough cut was going to be the final surface, so it needed it to be as flat as possible. I got some "ahhs" out of that one, and it did surprise me as I didn't think anything much about that kind of thing. As with all machine tools you can maintain a relatively quiet body; you have both hands to work with (well here is hoping anyway); the machine does all the work, what's the biggie.

About 20 years ago I got a new Laguna bandsaw in replacement for the chinese one I had. Carter guides, the whole 9 yards. I bought a bunch of their blades also. Wiggles like it's taking nips from a bottle when I am not looking. Never follows a line. I should shoot it, but instead I found an INCA I am restoring, and hope it will do better work.

One thing I do to follow a line is I place the square corner of the advancing kerf, on the line. I don't track the blade against the line.

I used to cut dovetail socket endgrain with a router when I started 35 years ago. I use a small bit, and climb cut for better control. The principle can be applied to other freehand routing, like doing inlay on guitars.

Re: Hand tools help machine tools

#3

band saw technique

Bill Tindall, E.Tn.

"One thing I do to follow a line is I place the square corner of the advancing kerf, on the line. I don't track the blade against the line." Agree

Another tip is to use a wide blade if you can, at least 3/8". I "ride" the back of the blade against the kerf and pivot the blade off this point to keep the advancing kerf on the line. Obviously this technique only works for cutting a curve. I control the cut so that any drift is outside the line. If I start to get drift I just back the blade up to the start of the drift point and continue the cut. Somebody was watching me one day and they wondered why I kept backing up. Apparently it never occurred to them that one could back up and restart the cut to shave off what was needed to split the line.

If I was better at spoke shaving I might be less picky about the band saw cut. :)

Re: Hand tools help machine tools

#4

Re: band saw technique

TomD

+1 on rubbing the back of the blade. Doesn't make sense, why doesn't it drift, but I is a useful reference.

Re: Hand tools help machine tools

#5

Re: band saw technique

Bill Tindall, E.Tn.

The back of the blade serves as a pivot point to rotate the blade front to orient the teeth on the guide line. I find it easier to orient the teeth by rotating off this anchor than trying to orient them as they wander freely in the saw kerf. Try it on an outside curve with a 3/8 or 1/2 " blade.

Re: Hand tools help machine tools

#6

Re: band saw technique

William Duffield

That's also the idea behind the Carter Stabilizer, which eliminates the side guides (blocks or bearings) and all the guides below the bandsaw table. It does take a "little" getting used to, like a vehicle or cart with rear wheel steering.