Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Table Saw Drive Belts

Posts

Table Saw Drive Belts

#1

Table Saw Drive Belts

Yonak

I'm having a difficult time finding matched belts for my Jet JTAS-10L table saw. I've gotten three sets and, with all of them, one belt is either too large or too small. Does anyone know of a supplier from whom I can get good truly matched belts ? This saw takes three belts.

Re: Table Saw Drive Belts

#2

Re: Table Saw Drive Belts *LINK*

Bob Entwisle in NJ

I've no experience with em, but this link is to a PDF for Browning Belts, and indicates that they will match belts etc. Maybe give Regal parts a call and ask.

http://www.regalpts.com/PowerTransmissionSolutions/Other/Belt%20Drive%20Monthly's/Form_9787E.pdf

Link to Regal parts,

http://www.regalpts.com/Pages/home.aspx

Let us know how you make out, my unisaw will need new belts someday.

Bob in NJ


Belt Matching

Re: Table Saw Drive Belts

#3

Re: Table Saw Drive Belts

Clementine

I went to a link belt on my table saw and drill press. It solved several issues. I don't know if link belts would work in a multiple requirement. Maybe someone on here can answer that.

Re: Table Saw Drive Belts

#4

Re: Table Saw Drive Belts

Lee Schierer in McKean, PA

Gates V80 series belts will match length.

Lee

Re: Table Saw Drive Belts

#6

Absaloootly

Mark Mandell - Gone Round In New Jersey

I've had Fenner (red link-belt) drives on the same JET saw for over 12 years. They are smooth, quite, and matched precisely.

The only thing to watch is to make sure that the little direction arrows printed on the links are oriented in the proper direction.

BTW, I use them on my band saw, jointer, and drill press as well.

Re: Table Saw Drive Belts

#7

Re: Absaloootly

Yonak

Mark, do link belts have to be matched or, since they are not rigid, simply the same size would work ?

I have never used link belts (my machinist friend also recommended I use them). Have you ever noticed them slipping ? I'm sure there's a tutorial on-line on how to tension them.

Re: Table Saw Drive Belts

#8

Re: Table Saw Drive Belts

Yonak

John, I imagine this method would cut down on vibration. It seems to me, with the tight quarters, however, I would likely have to remove the table to install this type of belt. Thanks for the suggestion.

Re: Table Saw Drive Belts

#9

Thanks for the links, Bob.


Re: Table Saw Drive Belts

#10

Count

Mark Mandell - Gone Round In New Jersey

links and they match; simple.

I have never stalled the blade on my saw. Not that I haven't tried you understand ;)

I would suggest, however, that before you install the new drives, you clean both of your sheaves.

I tensioned my belts with a piece of 3/4" rebar as close to the center of the belt loops as I could get. Provided your sheaves are parallel, tension on the 3 belts will be the same. Just for whatever, after about an hour's run time I re-tensioned them. Haven't touched'em since.

Re: Table Saw Drive Belts

#11

Re: Count

Yonak

Great, thanks, Mark. I'll order some belts tomorrow.

Re: Table Saw Drive Belts

#12

Go to a power transmission store

Pete in Holland MI

Order up "matched" belts from a "power transmission" store. Special care is taken for these belts. Belts from the local hardware store will have a degree of variation, as cost is key here.

Pete