Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Making a large mortise?

Posts

Making a large mortise?

#1

JL

Making a large mortise?

JL

How do y'all make a large mortise in a base?

I need to make uprights for a trestle table. I was planning on cutting the mortises into the bases for the uprights and then cutting the tenons for the uprights on a table saw. I would then smooth the tenons using planes.

The last time I did it, I chiseled it out (that was for the mortises for my workbench). I have a hollow mortise attachment for my drill press (an old Delta attachment). I also have some hand hollow chisels.

That got me to thinking of other ways to make the mortises. I typically do loose tenon joinery and use a router to make the mortises for aprons and such for tables, etc. Would I be better off using a router to get rid of most of the waste and then square the corners w/ a hand chisel or my hollow chisel mortise attachment? I don't have a preference as to how I do it - I would prefer easier and more accurate of course.

Re: Making a large mortise?

#2

Jack Guzman from Maine

Re: Making a large mortise?

Jack Guzman from Maine

I like to make large mortises by drilling,then squaring up with a chisel.Either a drill press with a forstner bit or if doing it by hand a brace and auger bit.With the forstner bit you can use a bit the same size as your mortise width,overlap the holes drilled and you end up with a relatively flat bottom. If you don't have access to a drill press or your piece won't fit in one,use some sort of guide to drill straight and chuck a forstner in a battery or electric drill.---Jack

Re: Making a large mortise?

#3

Ellis Walentine

Making a large mortise

Ellis Walentine

When Frank Klausz and I made five workbenches for an article in Woodworker's Journal, we used his hollow-chisel mortising attachment for his old heavy-duty drill press to cut the mortises in the trestle feet and top rails. The mortises were 3/4" wide but we used a 1/2" hollow chisel and made two rows of passes to get the width. This was into white oak, so it should be doable with your attachment, providing your drill press is robust enough to withstand the forces of mortising.

If that doesn't pan out for you, I'd take Bob's advice and drill a series of Forstner bit holes the width of your mortises and chisel the sides. If you bore the holes accurately, the arc of the hole provides an excellent reference for your chisel, so you end up with exactly that width when you're done.

As for the tenons, a tablesaw tenoning jig is fine up to a point, say 2", and then you should consider using a bandsaw. I don't know why you'd need to smooth tablesaw tenons; they should be fine right off the saw.

Ellis

Re: Making a large mortise?

#4

Re: Making a large mortise

Bill Tindall, E.Tn.

I have used 1/2" mortise bit in drill press for large mortises. Worked fine. However, stagger first set of square holes, then return and drill out the webs between. I was told by someone that should have known from experience to not drill a full sized hole without support on the sizes of the chisel or it could deflect and break.

Re: Making a large mortise?

#5

Re: Making a large mortise?

Stuart Johnson

One way is to make up a jig and use a router. Square up the ends with a chisel.

Re: Making a large mortise?

#6

Router for mortise

Henry (Raleigh NC)

I am in Stuart's camp here - a router. For larger pieces it is easier for me to take the tool to the work than the work to the tool.

I don't have a dedicated mortiser or a mortising attachment for my drill press. On a drill press I would have to set up a support table to hold a longer work-piece like a table base. For me that is way more work than setting up a router jig and pattern bit to mortise. Higher levels of noise and dust are the downsides to using a router.

Henry

Re: Making a large mortise?

#7

Re: Making a large mortise?

Jim Dillon

JL, I am also a big fan of loose tenons and haven't fashioned a regular tenon in years - especially since I got a Domino. Anyway, I built an umbrella table years ago with 1/2 inch thick by 3 inch wide mortises in the legs and feet. No problems after 22 years and the table is slid around a lot on the deck. Recently I used the same approach in building a bed but used a router template. It actually took longer to construct the template than cut the mortises. Long upcut spiral router bits are not inexpensive however, and a gentle approach is needed, especially in hard wood. While I have the equipment to choose other methods for making a mortise, I still like the router method. Here is a picture of a router template to make several 1/2 inch thick mortises. Jim


Re: Making a large mortise?

#8

Re: Making a large mortise?

Barry Irby

I am moving into the loose tenon Camp.

At an auction I bought a pallet that had 1000 sticks that were 3/8' by 7/8" and radius-ed on both edges and 16" long, for $10.

Went to a tool re-seller and bought a number of end mils from their box of Smalls. Lots of router bits and end mills and Hollow Chisels. Bought ten things for $100.

Started using floating tenons. So far, I like them.

I would use a router to cut the mortises. I have a template similar to the one pictured above. As they said, takes longer to make the template that to cut the mortise.

In stead of squaring the corners of the mortise, round the corners of the tenon. Takes seconds with a rasp.

Re: Making a large mortise?

#9

Re: Making a large mortise?

Mike in Zuni

Hey Barry, check your e-mail when you get a chance.

Mike

Re: Making a large mortise?

#10

Re: Making a large mortise?

William Duffield

I used to make them with a Powermatic hollow chisel mortiser, and before that with a mortising attachment for a drill press. I can't even give away the DP mortising attachment. It's just too much trouble to set it up. When I no longer had access to the floor standing mortiser, I used a forstner bit in a drill press and wide paring chisel, and rounded the corners of the tenons. Then I got a Festool DF500 Domino with it's loose tenons. Now I use a DF700XL Domino. I won't go back. If I need a tenon larger than 14 mm. x 27.5 mm. x 70 mm., I make the joint with multiple tenons.

Re: Making a large mortise?

#11

Ellis Walentine

Re: Making a large mortise

Ellis Walentine

Interesting, Bill. Stands to reason. Now I'm wondering how we made those 3/4" wide mortises with a 1/2" chisel.

Ellis

Re: Making a large mortise?

#12

Re: Making a large mortise

Bruce, a MN Galoot

Just like anyone else, one whack at a time :D

Seriously, you do what is needed with what you have.

Re: Making a large mortise?

#13

Re: Making a large mortise

AZ in Colorado Springs

I've used the "multiple forstner bit holes" method. If you begin with four small holes at the corners, say 1/4" (using a forstner or brad point bit), cleaning & squaring the corners is easier.

Re: Making a large mortise?

#14

Re: Making a large mortise

Don Stephan

Pray tell why did you make 5 workbenches - did the photographer make mistakes? That's a lot of bloodwood.