Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

First for me- BS blade cracked!

Posts

First for me- BS blade cracked!

#1

First for me- BS blade cracked!

Tony-Memphis

I've read stories, but this was the first time for me. I was cutting some small pieces and I started hearing a knock. Started the normal investigation protocol and saw nothing unusual. So, I spun the blade by hand and noticed a distinct bump. When I looked closer, I found a crack. After I removed the blade, it was very easy to finish the break. It was near the weld, but not right at the weld. Not sure how old, but it is a Highland Hardware 3/16 blade. I'm sure I've been using it a while. I don't abuse them and it probably doesn't have much run time. While I was inspecting, I noticed the lower thrust bearing didn't want to spin. It feels pretty rough. New blade and bearings on the way.... Still using the stock stuff with cool blocks. I've read that the fancy guides aren't worth the money. I wish the cool blocks fit better. Mine are small for the guide and they want to go all angled like when tightened. I glued a piece of veneer to two sides of the blocks to take up the slop. That works, but.... Glad it didn't snap while I was cutting...I'm sure that would have woken me up! Glad I had the old blade as a backup too. At least I could keep working.

Tony

Re: First for me- BS blade cracked!

#2

I have broken many

Bill Tindall, E.Tn.

1/4" coarse teeth blades don' t last a long time on my 14" saw. The flex over the wheel gets them eventually.

Re: First for me- BS blade cracked!

#3

Re: First for me- BS blade cracked!

Yonak

Tony, I've had more blades break than I care to count. It doesn't surprise me anymore. When I hear the telltale knock you speak of I know it's coming soon but I have never had the blade injure me from breakage. It usually tends to bunch up in some fashion in the top of the saw.

What surprises me is the break of your blade was not at the weld. As many times as I've had broken blades I don't think is was ever not at the weld.

Re: First for me- BS blade cracked!

#4

Re: First for me- BS blade cracked!

David Bair

Make your own perfectly-fitting "cool" blocks from end-grain white oak. They work as well as the carbonized blocks.

Re: First for me- BS blade cracked!

#5

Re: First for me- BS blade cracked!

Tony-Memphis

You know, when I was at a class once, I noticed their old giant band saw had wooden guides. I may give that a shot. Thanks. logic tells me that the rollers would be better, but I have read several reviews that say they don't work any better. I've never had any real complaints about the cool blocks and my band saw has always worked pretty well. I did notice when I was tensioning the replacement blade that the tensioner "felt funny." I've heard that some Jets had issues. Mine is pretty old and never had any issues, so I'm hoping it was just dirty threads or something. Been a good saw.

Tony

Re: First for me- BS blade cracked!

#6

Re: First for me- BS blade cracked!

William Duffield

I've broken lots, on a 12" bandsaw. Timberwolf people note that saws with wheels less than 14" break blades, due to how much they are bent going over the wheels. That helped a bit. I switched from metal to lignum vitae blocks. That didn't help much. I switched to Carter stabilizer (no blocks, one bearing) and I switched from 1/8" to 3/16" blades. That helped some more, but I still break them. They break anywhere, usually not at the weld. The blade I have in the saw has started knocking. I predict it will break the next time I try to use it.

Re: First for me- BS blade cracked!

#7

Re: First for me- BS blade cracked!

John K Jordan

Yikes, I've worn out dozens of blades on my bandsaws and never had one break, well, except on the sawmill. I had been concerned that a break would throw a blade out but all it did was stop instantly.

Is yours a 14"? I've used an 18” Rikon for a decade and I've heard that the larger wheels are gentler on blades.

However I've never used that small a blade; the smallest is 1/2".

I once made some bearing blocks from lignum vitae for the 14" Delta and they worked well - liked them better than the metal blocks.

JKJ

Have you lubricated the threads and moving parts of the tensioner? I think I used a dry lube because of the sawdust.

Re: First for me- BS blade cracked!

#8

Re: First for me- BS blade cracked!

Bruce, a MN Galoot

I have had bandsaw blade breaks. The blade has always stayed contained in the wheel housing, but it sure sounds like the whole saw is coming apart.

Re: First for me- BS blade cracked!

#9

variables

Bill Tindall, E.Tn.

Blades break from flexing as they bend over the wheels. The smaller the wheel the more they flex. 14" is about the limit for wheels to make blades last.

The wider the blade the stronger it is. The fewer the teeth the less blade between the gullet and the back.

The bottom line of it all. I haven't broken a 1/2" blade on my 20" saw either. But 1/4" 3 tpi blades on my 14" saw don't last long.

Re: First for me- BS blade cracked!

#10

Re: First for me- BS blade cracked!

Tony-Memphis

Yes, it is a Jet 14" with riser. No, I have never lubed the tension mechanism, but when I get the new blade and bearings, I will do that for sure as well as a thorough inspection of everything. I have owned this saw for almost 18 years I guess, but it has not seen a lot of use (weekend warrior). Been a good saw though. This is a 3/16" blade, btw. I have only used a 3/16 and a 1/2.

I did some reading last night on guides. I plan on trying wood. Easy, cheap, and plentiful! My Cool Blocks still have a fair amount of life left in them.

Tony