Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Torsion box questions

Posts

Torsion box questions

#1

JL

Torsion box questions

JL

I am going to be leveling some benches w/ turned legs.

As they will be 7 1/2' long.... I typically level things on my cabinet saw and its extension table.

That clearly won't be happening :).

So I figured I would make a torsion box. I figured I could easily rip a piece of plywood and have a nice 2' x 8' torsion box.

The following questions.

1/2" or 3/4" plywood? Or should I consider some other material for the outer layers such as MDF?

I was planning on using the equivalent of 1 x 4s on edge. I was thinking of jointing and ripping some 1 x 8s to get what I wanted - unless I found some decent 1 x 4s. Other thoughts?

Re: Torsion box questions

#2

Re: Torsion box questions

John McGaw

If "straight and weight" are the aim the you might be far better off using accurately-ripped 3/4" plywood for the inner structure and you can probably do just as well with 1/4" ply for the skins. The 3/4" ply will turn out to be more stable than your normal store-bought 1X4 and ripping 8' of it will be easy compared to trying to joint both edges of 1X4 straight and parallel. Use the strongest glue you can get your hands on, preferably one with decent gap-filling abilities as this will make up for lack of glue strength cause by plywood edge laminations. Or so goes my experience...

Oh, BTW, the last torsion box I did was accomplished with a rigid closed-cell foam inner structure and was all epoxied together. Super strong and light (although it was only a big mantle).

Re: Torsion box questions

#3

Re: Torsion box questions

Jim Dillon

JL, years and years ago I needed (or thought I needed) a 4' x 8' flat assembly tabletop, for, you know, making furniture. I made my torsion box from 1x2s (big borg store) and outer skins of 1/4 inch MDF. Just used regular Titebond II on all the edges with some screws on the outside 1x2s. I also screwed the skins down using countersunk holes. That tabletop was incredibly flat and rigid. And pretty awkward to move around. A torsion box is incredibly strong. Keep in mind, the dirt cheap doors found everywhere are just a very thin skin over cardboard as the support structure. In fact, I have used those doors left over from renovation projects as very flat assembly tables and they were perfect and very lightweight. But they are not quite long enough for your job. Since you have them, I would rip your 1 x 4s in half and use those for the insides, and 1/4 inch MDF for the skin. Nothing wrong with using 1x4s for the interior, but I think it is overkill. My thoughts. Jim

Re: Torsion box questions

#4

Re: Torsion box questions

Don Stephan

A torsion box requires an extremely flat surface on which to build it. I think the suggestion I found was to joint and rip to common width 5 or 6 2x4's, lay across sawhorses, and shim the sawhorses until very accurate winding sticks showed the 2x4's were flat and straight with no twist; then lay a 3/4" sheet of MDF on the 2x4's. If I remember correctly, my core was a lattice of 1/2' MDF, the edges 3/4" MDF, and the surfaces 1/4" MDF. My "clamps" probably were several sheets of 3/4" MDF. After it was done I screwed 1/4" melamine to each surface, then 1/2" plywood around the perimeter.

I'd suggest looking around first at several plans and choose one with which you are most comfortable