Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

A mallet

Posts

A mallet

#1

A mallet

John in NM




Second of a "series" -- I put it in quotes because these are tools and will be beat up and re-handled as they are used. It's literally a series though, because they are all made out of western US oaks, hard and dense, and all from places I've worked - first one I made around 2003 from an Emory oak branch from Kitt Peak in Arizona. This one is made from an oak section I picked up at Mt. Graham in Arizona - I don't remember which variety though.

After these (I have a few more heads made from the Mt. Graham wood), I have some Gambrel oak from the Sacramentos in NM drying. I'll make another mallet from it in a few more years, once the wood has thoroughly dried.

All these oaks were either windfalls or the result of DOT pruning. No idea what the local policies are, but oaks are unusual enough out here that I don't cut them down just for this stuff.

Re: A mallet

#2

Re: A mallet

Dick Coers

That could really bloody up your thumb! Really surprised no cracking in the head, looks great!

Re: A mallet

#3

Re: A mallet

Bruce, a MN Galoot

Nice! How did you manage to dry it without cracking?

Re: A mallet

#4

cracking

John in NM

I coated the ends with anchor seal and left the bark on for a few years. It helps that this is pretty dense oak so it doesn't shrink a whole lot.

The stuff I have from New Mexico cracks much more readily - I don't think its quite as dense as the Arizona species.

EDIT:

I picked up the wood for this one on the side of the road in 2008 or so.... it's been drying a while :D - probably why I got away with leaving the bark on for the first few years. It was probably dry enough several years ago, but I only got to thinking about it again when the trees around here blew down last year.

Re: A mallet

#5

Re: A mallet

Brian Holcombe

Beautiful work John! Great shape to the ball peen handle!

That mallet head is quite a nice piece of oak. I've set some locally harvested Goumi aside for a mallet head and plan to build one soon. It's been a test of my patience being that I'm really itching to make one but I know better than to cut the mortise before it's really dry.

Re: A mallet

#6

Re: cracking

John K Jordan

Ooo, If you like to make mallets I should send you a piece of dogwood and a piece of persimmon. Dogwood is my favorite - the one I use in my shop I made maybe 12 years ago.

I think persimmon would be good, very hard, dense, and strong - used to be used for golf clubs. I have some about 2-1/2" thick that has been drying for over 10 years. Send me an email if you want to try a piece. I don't have a lot of dry dogwood left but I think I have enough for a mallet head and handle.

JKJ

Re: A mallet

#7

That is a wonderful offer!

John in NM

I will definitely take you up on it! :D

I should know if my NM oak is worth using in a year or so, if it is I can send you some to try out. Or maybe I can find a piece of Algerita trunk around that's big enough for turning - stuff's this amazing yellow when fresh, makes Osage orange seem kinda drab even. No idea how it ages though.

Re: A mallet

#8

Re: A mallet

John in NM

Yeah, the first one I made in 2003 wasn't fully dry before I started, and it cracked slightly around the mortise after I had put it on a handle. It was dry enough that it didn't split radially though, so the crack doesn't really damage anything but the look.

Glad you like the ball peen handle too, I made several like it for various small hammers I had around. One was a stainless jewelers hammer, so used a stainless compression fitting wedge for it - came out pretty cool looking :D I have a pic of that one somewhere, but its not on the SD card I had in my pocket this morning.

Re: A mallet

#10

Re: That is a wonderful offer!

Bill Tindall, E.Tn.

And then there is Osage Orange. Excels in dense and pretty.

Re: A mallet

#11

Re: question

John in NM

This big one I've not used yet. The little one I made years ago gets used for anything that one needs a mallet for - chopping dovetails, adjusting molding planes, and closing paint cans. It's on it's third handle (made of Osage orange). It is a bit light for mortising, though I have used it for that. I had another I used more, but I recently broke its head - mesquite for the head didn't work so well, though it had held up for 20 years.

A friend (who still works at Mt. Graham) asked for a mallet for something to do with engine rebuilding (I don't remember what). I may give him this one as I think the long handle would work better there than in the wood shop.

Re: A mallet

#12

Yes, great stuff...

John in NM

I've used it mostly for handles, but it would make a great mallet head too. I can buy it in Albuquerque, but only in S2S 8/4. I may buy some next time I'm there and laminate a couple pieces to replace my mesquite mallet - that block was about 3 1/2" thick.

Re: A mallet

#13

Here are the older ones

John in NM




This last one is no more, though I might salvage the handle. Made that one around 1997.

The other is a small mallet, a very convenient size for general shop use tapping on whatever needs a tap.

Re: A mallet

#14

Re: Here are the older ones

jessecloud

Cool mallets. I bet when something gets tapped with one of those, it stays tapped!

Its a great feeling making something truly useful. I ground a custom shape into one of my card scrapers to help shape some curvy table legs. It actually worked and made my day!

Re: A mallet

#15

Thanks Jess...

John in NM

What did in the big square one was too much abuse though, it finally split when I was re-hanging a large axe. I've switched to a rubber mallet for that, but it doesn't work as well as a wood one.

I do really like making tools - there is a special satisfaction that goes with using them.

I may have some time off lined up the end of this month, we should get together at the Two Fools for lunch and beer.

Re: A mallet

#16

Re: Thanks Jess...

jessecloud

Sounds great. Gimme a call when you want to do Two Fools.