Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Veneer Thickness Characteristics

Posts

Veneer Thickness Characteristics

#1

Alan Young

Veneer Thickness Characteristics

Alan Young

Thanks for all the responses about my bandsaw blade question below- Now to a different but related topic. Veneer thickness characteristics. As I mentioned in my previous post my veneer work in the past has been with thinner veneers---ie .0024 or less. I have had overall acceptable success using veneers of this thickness in my vacuum press-probable because my panels were seldom longer than 36" or wider than 24"- meaning I could tape and glue-up my veneers and have them set flat in my press. As I anticipate cutting my own veneers in the future-My first question is-At what thickness does wood stop "behaving" as veneer and start "behaving" as solid lumber? This question has to do with moisture content and wood movement. Secondarily does the relationship of wood movement/thickness vary from species to species? and or type of cut ie quarter sawn vs flat sawn vs rift cut??? At this point I am thinking for a number of reasons-that I'd be aiming at veneers up to 3/16 thick....Knowing what "Behavior" I can expect from thicker veneer will effect the way I approach a couple of designs I have on the board---Thanks all

-Alan

Re: Veneer Thickness Characteristics

#2

-ie .0024 or less????

Dick Coers

One too many zeros? Less would be like half the thickness of paper. Didn't know they made it that thin.

I always cut to 1/8" thick, glue it down, then thickness sand to 3/32" (.094")

Re: Veneer Thickness Characteristics

#3

Alan Young

.0024 or less???? UGH! Yes .024 


Re: Veneer Thickness Characteristics

#4

Re: Veneer Thickness Characteristics

jessecloud

I was taught that anything thicker than 1/8th is gonna move.

1/8th is plenty thick for sanding if thats your concern, and it won't try to curl up when you put glue on it.

I guess I should have started with "What problem are you looking to solve?"

Re: Veneer Thickness Characteristics

#5

Alan Young

Re: Veneer Thickness Characteristics

Alan Young



I guess I should have started with "What problem are you looking to solve?"

I guess I'm looking to optimize the advantages of solid lumber and veneer. Perhaps that is a futile goal analogous to buying a multitasking machine such as the Shopsmith?

I was taught that anything thicker than 1/8th is gonna move.

1/8th is plenty thick for sanding if thats your concern, and it won't try to curl up when you put glue on it.

Yes-Two of my concerns. I have some 3/16 Sapele veneer. The stock is roughly 14" wide and I have pieces in 4 ft and 3 ft lengths. So I am curious to see what I can do with these pieces. I like the thought that I might be able glue this stock to thicker substrate, surround it with a hardwood frame and sand/plane the surfaces flat without worrying about going through the veneer.

Re: Veneer Thickness Characteristics

#6

Why...

Bill Tindall, E.Tn.

...".aiming at veneers up to 3/16 thick. " I aim for 1/16" or less because this thickness handles like typical veneer and it is thick enough to be robust in sanding, etc. The stiffness of what you propose is going to lead to stiffness and strength which will lead to difficulties assembling taped sheets and application. Put water based glue on one side of a 3/16 assembly and there will be no way to keep it from curling and tape will not hold it flat before the vacuum is applied. I had a tough time with the "fat" 1/16" as I recently worked. I have not had problems with shy 1/16".

Re: Veneer Thickness Characteristics

#7

3/16" 

Mark Mandell - Gone Round In New Jersey

I did that in walnut for the entry hall side boy


Glued onto 3/4" MDF.

The oil poly finish in the pic has "shrunk" down to show grain pores but every joint has remained tight. My success may be a function of the combination of walnut and a large number of coats of poly sanded back for a dead flat surface, but hey, it works.

This top, however,

was made from 1/2" stock in walnut and air-dried cherry. The lines open slightly at the pie points during the winter.

Re: Veneer Thickness Characteristics

#8

Ellis Walentine

Sawn veneer

Ellis Walentine

James Krenov told me to resaw to 1/8" and thickness to about 1/10", and that's always worked for me. In your case, sapele is pretty stable, so you could get away with thicker stock. Just remember to balance the construction, or else you'll have an awful lot of strain on the substrate as the veneer tries to cup or bow. I wouldn't advise edge joining the veneers to make a wider panel either.

If it were me, I'd have it thicknessed to 1/8" or less. A Timesaver or wide-belt sander is the preferred machine for this.

Ellis

Re: Veneer Thickness Characteristics

#9

Re: Veneer Thickness Characteristics  *LINK*

Keith Newton

Alan, I sure hope this veneer your turning out is some pretty special figure for you to be going to the trouble of slicing it up then gluing it onto a cheap substrate, otherwise, it sounds to me like you are wasting time. Sapele isn't that expensive, and is pretty stable as solid lumber as it is.

My last project was a Sapele dining table, and that is what I used for my substrate, but veneered over it with some highly figured veneer. If you haven't got a good source for some spectacular veneer, here is a link to the my favorite.

Sapele is near the bottom of the Full-length Exotic Veneers, with 4 types. Just click on one, then scroll down for descriptions, then click on the thumbnail for larger pics and specs.

These guys are great to deal with, and their discounts go up as the size of your order goes up.

Even with a Woodmizer sawmill that can cut some pretty good veneer, if I figured my time to saw and veneer a cheap substrate, it is cheaper for me to just buy the lumber, when I figure my time into the equation.


https://www.certainlywood.com/woodmenu.php

Re: Veneer Thickness Characteristics

#10

Could you elaborate?

Henry Higginbotham

I wouldn't advise edge joining the veneers to make a wider panel either.



Is there a reason this doesn't work well with thicker veneers?

Re: Veneer Thickness Characteristics

#11

Ellis Walentine

Re: Could you elaborate?

Ellis Walentine

Hi Henry,

Different woods shrink and expand by different percentages of their width. Though sapele's shrinkage coefficient is smaller than those of a lot of other woods, it will shrink as the MC goes down. The wider the board, the more net shrinkage you'll get.

You can veneer fairly wide surfaces if the veneer is thin enough, because the glue keeps it from shrinking the way solid lumber would. But, there is a relationship between the veneer thickness and the point at which it starts behaving like solid lumber. Just based on experience, I'm guessing that 3/16" thick sapele is already at or above that threshold. I'd feel fairly comfortable veneering it onto a relatively narrow substrate, but I wouldn't feel comfortable with veneering a wide panel of 3/16" sapele. The shrinkage forces would strain the glueline to the point of failure, or probably more likely, the wood would split at its weakest point(s). This is why most proponents of sawn veneers recommend a final thickness of less than 1/8", and even less on dense and brittle woods.

It's not hard and fast science, but rather something that you can either experiment with or take your chances on. I personally wouldn't chance wide glue-ups with 3/16" veneer.

Hope this explains my advice a little better. I welcome other opinions.

Ellis

Re: Veneer Thickness Characteristics

#12

Re: Could you elaborate?

Henry Higginbotham

Thanks, Ellis--it makes sense now. By the time I'd read this far down in the thread, I'd forgotten that Alan was talking about 3/16" veneer. I came by a sizable quantity of veneer recently in an auction, including some 1/16" makore that I intend to get into soon, and most of it will need to be spliced.