Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Table saw waste flipper

Posts

Table saw waste flipper

#1

Table saw waste flipper

Bill Tindall, E.Tn.



I was recently sawing the cheek waste from the male bridle joint. It produces a pesky piece of cut-off that jiggles against the blade and eventually may become airborne. If one tries to flip it away with a push stick the likelihood of it going airborne is increased.

The handy stick shown is stored on a nail in reach of the saw. It is simply a 1/4" dowel with a thin pointy brad in the end. I think it is important to choose a thin brad so that if it ever gets in the teeth it will not break any.

To remove pesky waste next to the spinning blade just spear it with the point and flick it harmless away from the blade.

Caution: remove waste flipper from saw blade before turning on the saw.

Re: Table saw waste flipper

#2

Re: Table saw waste flipper

Grant Smith

I too have the same issue. Historically speaking, I have used the eraser end of a regular old pencil to flip offcuts clear of the blade.

Given your solution, I am now thinking maybe a hybrid between your solution and mine is in order. I like yours because it offers a longer handle, but I like mine because the eraser is blade safe (except the ferrule, which is thin tin anyway). Maybe a dowel with a small rubber chair foot on the end...

Or, is it better to have a thinner flipper, in case it gets in the blade? Dunno.

You are very correct in that one must still exercise caution when determining what is a safe move and what isn't around a spinning blade.

I always wear a thick leather shop apron when using the table saw.

Thanks for the post, Bill!

Regards,

Grant in Iowa

Re: Table saw waste flipper

#3

advantages

Bill Tindall, E.Tn.

Spearing the waste with the point was the most secure way to flip it, more positive than a friction contact between flipper and waste. The long handle made for good flipping. The thin brad would have no effect on the blade. It is the size of a staple and we ALL have sawed a Lowes lumber staple or two :( .

Re: Table saw waste flipper

#4

Re: advantages

Bill Howatt

I agree the little bit of steel would not be an issue but if it is a concern then something like a #4 or smaller (real) brass screw could be used and ground to make a sharp point and even reduce the diameter if desired.

Bill

Re: Table saw waste flipper

#5

Non-Ferric

Mark Mandell - Gone Round In New Jersey

Sub a piece of 12 ga. copper or brass wire with a point and held in with CA.

Re: Table saw waste flipper

#6

Re: What Would Happen With A SawStop?


Re: Table saw waste flipper

#7

Re: What Would Happen With A SawStop?

Bill Tindall, E.Tn.

I would suggest turning the saw off and removing waste after the blade has stopped if you think you can't keep the tip out of the blade, no matter what saw you own.

Re: Table saw waste flipper

#8

Actually

Mark Mandell - Gone Round In New Jersey

That's pretty much what I do already. I've had a kick-stop paddle installed on my saw for many years. When the cut piece clears the back of the blade my left knee hits that switch, even when doing multiple rips. I make more use of the switch box that some others, but I'd rather wear out a switch than have parts reattached.

Re: Table saw waste flipper

#9

Re: What Would Happen With A SawStop?

Stuart Johnson

Accidents do happen even to the most experienced. Take a look at John Lucas's thread over on the turning board. A very experienced turner just dinged his thumb a bit. In the case of the stick with a point a flick and an instant of distraction could cause the tip to contact the blade. It is so small it won't hurt the blade but my question was what would happen in that case to the SawStop. FWIW, I regularly use a ground Allen wrench to flick segments away and find it very safe.

Re: Table saw waste flipper

#10

Bandsaw

John K Jordan

We have a similar issue at the bandsaw, but with somewhat less hazard if the offcut contacts the blade. Little pieces constantly have to be cleared from around the blade. I'm not about to turn off the saw a dozen times while working but one of my slender push sticks does the trick. A shot of compressed air also works.

JKJ

Re: Table saw waste flipper

#11

Re: What Would Happen With A SawStop?

William Duffield

If the stick is an insulator (e.g., wood), it will not trip the brake.

Re: Table saw waste flipper

#12

Re: Unless…

William Duffield

If the piece of wire in your flipper was long enough to complete a circuit between the spinning saw blade and the saw table or metallic part of the insert or the riving knife.

Instead of inserting a brad, why not just sharpen the end of the stick in your pencil sharpener?

In Steve Latta's DVD on making ornamental bandings for federal furniture, he shows a technique for getting very small pieces of glued up wood blocks away from the saw blade. He attaches a piece of flexible tubing to the stop block, and puts the other end in his mouth. After each piece of banding drops off the blade and slides onto the saw table, he moves it away with a small puff of air. Slobber is a potential problem, so although he has several SawStops available, he uses an old Powermatic for this process.

Re: Table saw waste flipper

#13

Re: Unless…

Stuart Johnson

A shop vac can also be used for very small pieces.

Re: Table saw waste flipper

#14

Re: Unless…

William Duffield

Not if you are wanting to glue up some banding from all the little pieces. (Search google images for"inlay banding design" for some incredible examples.)

Here is an alternative to the SawStop: :D

http://www.leevalley.com/us/newsletters/Woodworking/2265/whatisit.htm