Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Chop saw cut question?

Posts

Chop saw cut question?

#1

Chop saw cut question?

Barry Irby

I had an ancient chop saw for many years. Sometimes I used it to cut mitered corners on small boxes. It worked well. The saw got stolen in the great tool robbery. I bought the Makita Compound miter saw mentioned below. I tried to cut miters on some thin (3/16") walnut about 3" wide/tall. They were sloppy. I stood the pieces against the left/low fence. The cuts came out off vertical. I corrected them on the TS.

Trying to figure out what the problem was. Checked the blade for vertical. It is. I think the problem is the fence is low on that side to all the blade to angle off vertical and the pieces were not fully supported. Maybe I should have angled the saw the other way and use the right side/taller fence Or tipped the saw to 45 off vertical and laid the pieces flat on the rotating table. Or used an auxiliary fence.

Any suggestions/advice? (not used to the "compound" function.)

Re: Chop saw cut question?

#2

Re: Chop saw cut question?

Dick Coers

How sharp is the blade. Lots of teeth? Some miter saws don't like shaving off a bit of wood, and you will get a different cut than when you have wood on both sides of the blade. Lots to tune up on some saws, I'm not fond of Makita saws, especially the big ones!

Re: Chop saw cut question?

#3

Jesper, Denmark

Re: Chop saw cut question?

Jesper, Denmark

First thing I did was replace the Makita blade with a Freud blade specifically designed for smooth cut-offs. Never looked back. Cuts smooth as glass and in the right angles. No problems with shaving off slivers to sneak up on exact dimensions.

Only complaint is blade wobble during acceleration. You have to wait til blade is at full speed to get an accurate cut.

Re: Chop saw cut question?

#4

Dick, Jesper....

Barry Irby

The blade is the blade that came on the saw. Its a 10" blade with maybe 80 teeth and very little use. It seems to cut well on most cuts. In fact I was impressed with it "out of the box".

I did notice that it did not like this thin stock.

Jesper, do you know exactly what blade you have? Might be time for an upgrade.

Re: Chop saw cut question?

#5

Re: Chop saw cut question?

Larry Clinton At Frankfort, (Central) Indiana

I have an older Dewalt CMS, I didn't get accurate cuts with it until I installed a Forrest ChopMaster Saw Blade, after installing that and aligning the saw I get very accurate cuts. I always do allow the saw to reach full RPM's and feed reasonably slow (too slow in thicker stock does seem to "heat" the blade and cause blade warp and poor cuts). With proper feed rates I get excellent results.

Re: Chop saw cut question?

#6

Re: Chop saw cut question?

George Koch

Barry, along with the suggestions of a better blade, are you saying you were trying to cut a 3" x 3/16" hardwood miter without any vertical support by a left side back fence extension in place. As I look at pictures of that model, it does have one.

Re: Chop saw cut question?

#7

Fence/support

Barry Irby

There is a fence on the left side of the blade, but it is low and angled to allow the saw to tilt to the left. So the bottom inch was supported but not the top half. I need to go look at the saw and see if that fence can be flipped into another position to be a tall fence on the left.

Re: Chop saw cut question?

#8

Jesper, Denmark

Re: Dick, Jesper....

Jesper, Denmark

Not exactly, but it is a 12 inch, not 10, and a Freud specially designed for smooth cut-off cuts.

Re: Chop saw cut question?

#9

Look for the sub-fence

Tim Greif - West of Chicago

Most Makita saws have them. It rotates into position to create a higher fence on the left side of the blade when not cutting bevels. If yours is missing, go to ereplacementparts.com and search for your model. It shows the subfence.

Re: Chop saw cut question?

#10

Finally - someone with my problem

Terry Alexander

Barry,

I gave the same saw and have had for years. I have tried Annaba, Freud, and even the expensive Tenru blades. Just can't get that perfect 90 degree angle from 2 45 degree cuts. I have tried everything I know and just can't nail it. Good enough for most stuff, but if I want a perfect joint, I go tot he TS.

I'll be following this thread to see what our fellow members suggest.

Terry Alexander in West Texas

Re: Chop saw cut question?

#11

Re: Chop saw cut question?

John in NM

Send me your address, I have a Freud like Jesper describes only 10" that you can try. I don't use it much as my regular use saw is an 8.5" slider.

If it works keep it, if not ship it back to me.

(jdowney"AT"plateautel.net --- that makes sense right?)

Re: Chop saw cut question?

#12

Re: Look for the sub-fence

Barry Irby

I have the sub fence, but even with it in place, the top of it leans back to the left leaving the top edge unsupported. I think what happened in my case is the thin piece leaned back and the bottom stayed in place, giving me some sort of strange curve or slight angle. The piece was around 3" wide and this created about a 1/32" gap under a square. The right side fence is vertical, but the body of the saw comes down onto your hand. I think what would have worked would have been to stick an auxiliary fence in place with double stick tape and then cut through it. This would have provided complete and consistent support.

Re: Chop saw cut question?

#13

Re: Chop saw cut question?

Jim O'Connor

I have the Makita saw and always use a scrap piece of 2x4 that has been squared on the jointer as a back up due to the low fence . This also seems to prevent some deflection in the piece being mitered.

Re: Chop saw cut question?

#14

Re: One other issue I forgot to mention

Larry Clinton At Frankfort, (Central) Indiana

Before I changed blades I also found one other issue. I found I could not hold the work-piece against the fence tight enough to prevent some drift during the cut, as the fence was pretty slick. I installed some fine grit adhesive backed sandpaper on the fence and it eliminated the problem. The movement was slight prior to installing the sandpaper (maybe .010 ~ .015", but was enough to prevent perfect miters.

Re: Chop saw cut question?

#15

Re: Chop saw cut question?

Johanna Johanson

Sorry you are having trouble. I have a Makita LS1080 that I bought at least 15 years ago. It is absolutely accurate and cuts really smoothly. I am still using the blade that came with it, although I have had it sharpened.

I wonder if your saw has been dropped or used on a very thick piece of wood that caused the blade to twist.

Re: Chop saw cut question?

#16

John, I got the chop saw blade.....

Barry Irby

Thanks, Its a beauty and cuts beautifully too. Its a keeper. I will make a donation to WC.

Re: Chop saw cut question?

#17

And I did....

Barry Irby

Contribute that is. Glad to support Wood Central. And thanks again.