Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Questions on gilding????

Posts

Questions on gilding????

#1

Questions on gilding????

Barry Irby

Anybody do gilding? My friend bought a harp to resell. The tuner said it would improve resale value if he would have the gilding redone. He seemed to think gilding was very difficult and best left to the experts. I have witnessed people gilding a few times, but never even tried. Did not think it looked terribly difficult and while I'm not about to learn how on this harp, I was just wondering how hard it really is and how expensive it would be to get into it.

Re: Questions on gilding????

#2

Re: Questions on gilding????

Dick Coers

I've done some on vessels. Can't say if I did a good job or bad, never seen a professional job up close on turnings. It's not hard, but I've only used dutch metal leaf, not real gold. If the instrument is really valuable, I'd stick with a professional.

Re: Questions on gilding????

#3

Ellis Walentine

Worth a try *LINK*

Ellis Walentine

I've done some gilding on furniture projects, and it was not difficult but it did require a steady hand and a delicate touch. The gold leaf is expensive, of course, but other than that, there aren't many tools or other supplies involved -- sizing, agate burnishers, gilding brush, etc. I'm sure you can find excellent resources on YouTube and elsewhere. My old pal David Marks has taught workshops around the country on metal-leafing and patination. Below is a link to a 90-minute DVD he produced on the subject.


Gilding and Patination DVD

Re: Questions on gilding????

#4

Re: Questions on gilding????

Ralph Lipeles

I've seen it done many years ago putting office names on glass doors. It was very straight forward. Paint the rabbit hide glue on the door. Trim the glue as required with a razor blade. Then run a special brush through your hair to get static electricity into it. Use the brush to lift a sheet of gold leaf and place it over the trimmed hide glue. Rub it with a soft cloth and then trim the excess gold leaf with a razor blade.

I expect that doing flat surfaces would be pretty easy but ornate curves and crevices could be pretty tricky.

Re: Questions on gilding????

#5

Re: Questions on gilding????

John McGaw

Constantine's (remember them?) used to sell a do-it-yourself gilding kit with instructions and fake leaf. I did a couple of test samples with that and what I did looked pretty decent and wasn't too difficult. Then again I didn't try anything challenging. No idea where that stuff went during the last move.

Re: Questions on gilding????

#6

Re: Questions on gilding????

Rick Haverstock

Barry, it's not that tough, especially on mostly flat surfaces. I started out doing the David Marks thing and branched out to other objects. The pic is of the name boards for our boat. This is 24K gold (weather and tarnish resistant) on hand carved mahogany stock. If there are a lot of cracks and crevices use the so-called "patent gold" which has the metal adhered to a paper backing. I use a make-up brush (big and soft), cotton balls, and Rolco sizing. I've done cabinet doors. wood turnings, and a Chinese chest using variations on the technique but can only lay my hands on the name board pic at this moment.

Rick Haverstock


Re: Questions on gilding????

#7

Where is source for gold leaf book?


Re: Questions on gilding????

#8

Re: Where is source for gold leaf book? *LINK*

Bob Entwisle in NJ

Hi Gary,

Is there anything you can't get on Amazon???

Bob in NJ


Gold Leaf

Re: Questions on gilding????

#9

Another Gold leaf source *LINK*

Bob Entwisle in NJ

Or if not an Amazon fan

Bob in NJ


Gold Leaf

Re: Questions on gilding????

#10

2nd source on west coast-message in-thanks


Re: Questions on gilding????

#12

Re: Yes

Bob Entwisle in NJ

Ah yes, Privacy,

I remember that, I think it went south around 2000 or 2001:)

Merry Christmas everyone!

Bob in NJ

Re: Questions on gilding????

#13

Clint Searl

Re: Questions on gilding????

Clint Searl

Gilding with size is straight forward, and achieves very good results without a lot of challenges. Here's one project using both 24K and white gold leaf.