Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Back to my jointer......

Posts

Back to my jointer......

#1

Back to my jointer......

Barry Irby

I have a Rockwell 6" long bed Jointer I bought new in 1972. It has been "grumbling" fr a long time. I thought the bearings were going bad. Thought about replacing the bearings. Expanded that thought to replacing the head with a Shelix head. E-mailed Byrd about it and learned that there are at least five different head/shaft designs that might apply. They suggested taking it apart, sending them the head and letting them install new bearings on the new head and returning it. Got distracted by a tool auction, but got outbid on a like new Powermatic jointer.

Last night I took the old head out. Never as easy and it sounds. Had to get into the far side of the machine to get the safety cover off the pulley and shaft. Shuffle things around and crawl in under things. Finally go it. Turn s out the pulley was a pot metal one and has come loose. As they would say on the East Coast of Carolina, it had momicked the shaft and itself. The key was reduced to a triangular shape and the shaft was galled badly. One entire side of the key was gone. The shaft was nowhere near round. The pulley was just floating on this mess. The guard had made it difficult to determine what was happening and so had the position in the shop. I suppose the lesson is that we should have our machines setup so that we can inspect them thoroughly from time to time.

I have decided to go ahead with the Byrd Shelix Cutterhead. Turns out the bearings were OK, but I am not sure what it would take to get the pulley firmly mounted and I have grown weary of setting the knives. The old head did not even have jack screws under the knives.

Than ks for the discussion we had on this a few weeks ago.

Re: Back to my jointer......

#2

Re: Back to my jointer......

Dick Coers

New motor too? Or take it to a motor shop for a shaft buildup? That's going to be an expensive old jointer, real quick!

Re: Back to my jointer......

#3

Motor is fine.....

Barry Irby

It was the shaft on the head that was butchered. Procrastination does not pay. Its been grumbling a long time and I just did not look at it closely enough. It was cutting with scallops in the edge unless I went very slowly. I leapt to the conclusion the bearings were bad, causing the head to have run out.

I considered taking it somewhere and having the shaft built up, but I did not know where or how much it would cost, and I wanted a new Shelix head. Merry Christmas to Me. Man I hated changing those knives.

And don't be calling my jointer old. ;) Its been waiting a long time for me to get busy making furniture. I feel bad letting that cheap pulley beat the shaft to death.

Re: Back to my jointer......

#4

Re: Motor is fine.....

Larry Clinton At Frankfort, (Central) Indiana

I really think you will be very pleased with your decision. The first time you hear the head "rapping" against a buried metal object and damage 2, 3 or 4 inserts. You will find all you have to do is rotate any "chipped" inserts, or at worst replace one or two broken ones at about 4 bucks apiece in about 10 minutes and your back in business! No setup, no measuring, just remove the insert, clean the pocket well, then either rotate or replace.

The other giant advantage is that the inserts will outlast several knives (on each of the 4 cutting edges), and problem woods will no longer "tear out". I have ran many boards through my joiner and planer without any issues, some of the boards would have required wetting, and or cleanup to remove tear out with my old equipment. I think I have broken 2 or 3 inserts in about 4 years of fairly heavy hobby shop usage. I have "chipped" another 4 or 5 during that time that I rotated.

My Joiner is an 8" Grizzly with their segmented carbide head, planner is a 20" stationary with a Byrd head. Both work equally well, I can't see much if any difference in the finish. With either machine I normally can sand out any tool marks with 100 grit in a short time

Re: Back to my jointer......

#5

Those zinc pulleys are awful...

John in NM

We replaced a bunch of them on the telescope (yes, millions for a telescope and someone put a bunch of $5 pulleys on it) that had a tiny set screw installed over the key. Trouble is an 8-32 thread in zinc won't bite hard enough to hold the pulley tight - they'd been modified to work in an existing system and the only screw they could use was that tiny one.

Its well worth getting a couple cast iron or steel pulleys to replace any zinc ones - obviously you will already get a new one for the head, but check the motor too and get rid of the pulley if it's zinc (ie pot metal).

Re: Back to my jointer......

#6

Re: Those zinc pulleys are awful...

Barry Irby

Where does one buy better pulleys?

Re: Back to my jointer......

#8

Re: Those zinc pulleys are awful...

John in NM

In addition to local bearing suppliers the easiest places are McMaster Carr, MSC, and Grainger. Often you can also find them on Amazon or Zoro tool.

You can search for either pulleys or sheaves, some suppliers refuse to call them pulleys.

Re: Back to my jointer......

#9

Re: Those zinc pulleys are awful...

walta

After 20 years the grease in sealed ball bearing in your motor has turned into waxy gum. The bearings could seize up at any moment the motor shaft will likely be damage much like cutter shaft.

Walta