Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Lion Miter Trimmer Instructions

Posts

Lion Miter Trimmer Instructions

#1

Lion Miter Trimmer Instructions

Don Orr

I just picked up a nearly mint Lion Miter Trimmer (from 1978) off Craigslist locally for a very good price. I have looked around the internet for the instruction manual and can't seem to find anything. The original website is defunct. I found some videos but I'm a paper-in-hand type. If anyone might have a copy they could scan and send via email or even photocopy and mail I would greatly appreciate it. I would gladly pay any costs involved. This unit even included the optional top cut device.

Also, does anyone know of a sharpening service that handles these knives? I haven't tested it yet but the seller said it could use a honing, which I can probably manage, but just in case I mess it up I would like to know where I could send the knives for real sharpening.

Thanks!

Re: Lion Miter Trimmer Instructions

#2

No directions but sharpening

Gary Smyth

should not be hard to find. Look for a industrial shop that services the paper industry, large print shop, or a place that does ductwork. That knife is a shear and although you will have to remove the knife to take or send it out, the sharpening should not be a problem. Reinstalling it to cut properly might be. Take pictures before disassembly and note clearances and the number of turns of the lever nut. In the back of my mind I seem to remember that 1/16 is the max shaving.

Also keep well out of the way of others, especially kids. This can be a dangerous device.

Re: Lion Miter Trimmer Instructions

#3

Ellis Walentine

Re: Lion Miter Trimmer Instructions

Ellis Walentine

Hi Don,

This is a pretty simple piece of gear. Do you have a specific question about it?

Ellis

Re: Lion Miter Trimmer Instructions

#4

Re: Lion Miter Trimmer Instructions

Ralph Lipeles

Years ago I picked up a Lion trimmer at a local flea market. The cutters had been abused and actually had small nicks in a few places. I honed them down on my horizontal belt sander, just holding the the cutter with my hands and trying to maintain the previous sharpening angle. I then used oil stones on the surface that I had just honed and on the back side. They were razor sharp and cut perfectly.

Re: Lion Miter Trimmer Instructions

#5

Re: Lion Miter Trimmer Instructions

Don Orr

No specific questions right now but thanks Ellis. I have not had a chance to try it yet-I just got it yesterday.

Thanks for the replies!

Re: Lion Miter Trimmer Instructions

#6

very simple machines

Dick Coers

Almost like asking for an instruction book for a hand plane. LOL Maybe Grizzly has one on their knockoff machine?

Re: Lion Miter Trimmer Instructions

#7

Re: very simple machines

Hank Knight

After spending time over on Hand Tools, I'm not as sure as I used to be that hand planes are simple tools. :D

Re: Lion Miter Trimmer Instructions

#8

Re: very simple machines

Don Orr

I thought the same thing Dick-thanks.

Re: Lion Miter Trimmer Instructions

#9

Re: very simple machines

Don Orr

I totally agree!

Re: Lion Miter Trimmer Instructions

#10

Re: Lion Miter Trimmer Instructions

Tony - Memphis

I have a knock off. I have not had to sharpen it yet, so I can't offer much there. Mine came super sharp.

A couple of notes....there are pins to set the angle of the fence. Those can be adjusted - might want to check them. Take very small nibbles. Mine has enough slop that if I push the piece against the blade, then retract the blade, I get a very fine cut. Watch out for tear out on non-rectangular pieces. I use shimes of paper, tape, etc. when fitting.

Nice tool I don't use it often, but it sure is handy when I do. Oh, hold the work very tight - the cutting action tends to pull the work piece towards the blade. You can get weird cuts that way.

Tony

Re: Lion Miter Trimmer Instructions

#12

Re: Here's a couple links on instructions

Don Orr

Thanks for those links-I never would have thought to look at Woodcraft for instructions.