Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Failing sanding belts Question?????

Posts

Failing sanding belts Question?????

#1

Failing sanding belts Question?????

Barry Irby

A few years ago I stopped at a Abrasives store/manufacturer who happens to be about fifteen miles from my house. I had them make up what I thought was a lifetime supply of 4 X 24 sanding belts. I have not used as many as I thought I would so I have about 80 percent of them still on the shelf. Recently I got out the sander and put a fresh belt on it and tried to sand something. The belt failed Instantly. Tried another, and another. They all failed upon contact with the surface. Most of them shredded themselves running through the sander.

Apparently these belts have a shelf life. These are the reversible ones that have the nylon or fiberglass reinforced tape joint. Should I be offended? Did I save them to death? should I take them back? I bought them wholesale, so they were less than retail, but not cheap. I assume the other fifty or so will fail just as dramatically.

I have some of the old single direction ones left from Sears that are worn out and probably 25 years old. My packrat gene forced me to save them. They are pretty much useless but they will still run.

Re: Failing sanding belts Question?????

#2

Re: Failing sanding belts Question?????

Henry (Raleigh NC)

Barry:

I have had the same experience.

I don't recall where I got the advice, but I now store my unused belts in the climate controlled basement. In the heat and cold cycles of my sometimes used shop, the adhesive of belts did indeed fail. It has been sometime since I changed belts on my sander, so I can't promise that inside storage is a cure-all. I do know that it helps extend the shelf-life.

I do know that manufacturers don't recommend buying a lifetime supply, for this very reason.

Henry

Re: Failing sanding belts Question?????

#3

Re: Failing sanding belts Question?????

Yonak

Barry, I, also had the same experience. I have found that lessening the spring pressure of the belt sander on the belts has helped. I put a block against the tensioning lever. Finding the right amount of pressure so the belts don't slip off but don't break is the key. ..Not a perfect solution but it has helped me to get some use out of my lifetime supply of belts.

Re: Failing sanding belts Question?????

#4

Known issue for years now

Dick Coers

I've read about guys that try to glue them back together, but no great fix that I know of. If you take them back, they'll probably tell you it's not their fault.

Re: Failing sanding belts Question?????

#5

Re: Failing sanding belts Question?????

Jim Dillon

Barry, same experience here but the time period was probably greater than 10 years ago when I stocked up. Failure varied a bit by grit with IIRC the finer grits lasting longer. Lesson learned. Now I only stock up a few at a time in the grits I use. Jim

Re: Failing sanding belts Question?????

#6

Re: Failing sanding belts Question?????

john lucas

Same problem but mine were only about 5 years old. As a wood turner I don't use my belt sander as much as I used to. Had to rebuild a kitchen counter top and pulled out the sander and every belt broke instantly. Had to go to my local hardware and pay a rediculous price some belts to get me through the project.

Re: Failing sanding belts Question?????

#7

same here only buy what i need now

del schisler

i bought 10 belts won't mention mfd, but all failed right off the start , found out that they were to small dia. after some talk they made some new ones and replaced my belts and than all was good, never bought from them again tho

Re: Failing sanding belts Question?????

#8

Re: Failing sanding belts Question?????

TomD

I had this issue with 1x36 belts this summer, every one I put on the sander blew apart at the joint. Some did a little work, some exploded instantly. They weren't new. Then when I got to the last belt it held up, different manufacturer. This doesn't happen with name brand belts I have purchased like those from Kilngspor, or for my 2x72 sander. General view is you can't join belts in the shop.

Re: Failing sanding belts Question?????

#9

Bring them back

Ralph Lipeles

I would definitely bring them back. If they have a shelf life, it should have been noted someplace. Since the seller saw you purchase a large quantity, he/she should have mentioned a shelf life problem.

Re: Failing sanding belts Question?????

#10

Re: Failing sanding belts Question?????

Larry Clinton At Frankfort, (Central) Indiana

Doubt you can do much about them except use them for hand sanding. I had the same issue, only had about a dozen about 5 - 10 years old. I cut some of them down and used them on sanding blocks.

It is a know issue, and several people had tried to re-connect the belts, but from what I have read on hear no one was very successful!

Re: Failing sanding belts Question?????

#11

Re: Failing sanding belts Question?????

wayne carson

I had the same problem and blew up about $60 worth of belts before I realized that what was happening it was the tape on the back was letting go. I got some wide filament tape and removed the old tape and put the tape where the filaments would span the joint and carefully cut the tape with a utility knife. Then I crossed my fingers and bingo it worked so I did my other old belts I also bought a bunch o belts many years ago and didn't know that the tape has a shelf life not the belt.

Re: Failing sanding belts Question?????

#12

Re: Maybe what I need to do is....

Barry Irby

take them back and see if they can remanufacture them. The problem with remaking the belts is that I use so few of them now that they would probably fall apart again by the time I need them.

Next time I am in the area I may pull in and talk to them and see if they have any ideas.

When I was there last time I was struggling with the belt on my Performax. The seam on it was failing. They confirmed what I read here, that such joints can not be fixed "at home". They offered to make me one, but I passed because I could buy one at WoodCraft and they apparently knew how to do it and I did not have to depend on somebody reinventing them.

Re: Failing sanding belts Question?????

#13

Good tip Wayne!