Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Working on my Performax?????

Posts

Working on my Performax?????

#1

Working on my Performax?????

Barry Irby

A week or two ago I posted questions about the conveyor belt on my Perfomax slipping. I have a Klingspor belt that has a very slick back. It tracks better than the cloth backed one, but it is also "brittle". Based on suggestions I got here I took the belt off today and cleaned and waxed the table and slightly roughed the surface of the drive roller with sand paper. I put the belt back on and realized the inside of it was dirty. Pulled it off and wiped the inner/back side. Got a bunch of black sooty looking dust. Put the cleaner belt back on and tightened the belt to its previous tightness. Then I tightened it a "quarter" turn. It's not tracking perfectly, It creeps slowly away from the motor.

I'm still struggling with a couple of questions. What was the black stuff? How do I make it track toward the motor? (Tighten the belt on that side?) How will I know I have the belt too tight?

Re: Working on my Performax?????

#2

Do you have the....

Brian Roberts

manual for your machine?

Have you followed all of the adjustment instructions in the manual?

What model # is yours?

I will look at my manual after work.....it has quite thorough adjustment instructions.....IIRC

Re: Working on my Performax?????

#3

Re: Do you have the....

Barry Irby

Brian, I do not have the manual. I bought the machine used about a dozen years ago and the former owner gave me what he had, but did not have the manual.

I have noticed that some similar machines have little wrenches that are captive and hang on the adjustment bolts. I do not have those. Don't know why. Those wrenches are small and have about two ingh handles on them, suggesting that not a lot of force should be applied to the adjustment. Any help you can give would be appreciated. IIRC the belt tends to run "uphill" or toward the tighter end.

This tends to go against my grain. I would rather work with my tools than on my tools.

Thanks

Re: Working on my Performax?????

#4

Re: Working on my Performax?????

Ken Krawford

Barry, I went through hell trying to get a new belt to track properly. I DO have the manual that came with my sander and I followed the belt adjusting procedure exactly as specified but could never get it to track properly. I finally figured out that the manual was wrong and their directions were in fact backwards.

The belt must be LOOSENED on the side it it drifting towards and TIGHTENED on the side where you want the belt to move to. Once I figured this out I was able to get perfect alignment and it has stayed this way.

Re: Working on my Performax?????

#5

Re: Working on my Performax?????

Barry Irby

Thank You. That is what I thought I remembered from my days on the farm. I really did grow up on a farm and we had a few machines that were belt driven. I recall that the belt ran uphill or toward the tighter side. Somehow that does not seem obvious. Seems like it aught to go toward the looser side, but no, it goes the other way. On some of the machines the pulley had a crown in it and the belt would sort of oscillate back and forth and then settle in.

I had the cloth backed belt and thought I had it running right. Sanded some panels that were over 16" wide. Did not realize the belt was creeping away form the motor until it scrubbed against the frame, ruining the edge of the belt. If I had caught the little bast@rd sooner I would have taken it back. Did not feel WoodCraft should suffer for my stupidity.

Re: Working on my Performax?????

#6

Re: Working on my Performax?????

John C Lucas

That is correct, tighten the side you want it to move towards. I also have the belt from Klingspor and constantly have tracking problems. Mine is also an older performax.

Re: Working on my Performax?????

#7

Re: Working on my Performax?????

Barry Irby

This at least my third belt. The one that came on it when I bought it used tracted fine for years without any fiddling. I got the second one to track well too. Still fiddling with this one. Just not something I am not used to keeping an eye on.

Re: Working on my Performax?????

#8

Re: Working on my Performax?????

TomD

When I was making guitars I had one of the early machines. They had problems with parallelism in the cut. I called the manufacturer (since sold to some big company?). He gave me a very detailed adjustment protocol that was definetly not in the manual. Might be worth a call.