Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Workbench Raised!

Posts

Workbench Raised!

#1

Workbench Raised!

tom

After watch a video series, Paul Sellers. I decided it was time to increase my workbench height. So yesterday I had my wife help me tip the bench tp, 30"x84" x2 1/2" solid maple up onto a set of horses. I then made up riser blocks 3.75" and then re-installed the to today after getting longer fasteners.

So after clamping some stock in the vise and doing some cross cutting I am well pleased! Wish I had done it sooner. My back will be grateful!

Re: Workbench Raised!

#2

Re: Workbench Raised!

John K Jordan

What height did you end up with? Is there a formula for workbench height for a person's height?

Re: Workbench Raised!

#3

Re: Workbench Raised!

tom

My bench is at 39".

Re: Workbench Raised!

#4

Re: Workbench Raised!

John K Jordan

How did you come up with 39"?

Is there a suggested workbench height for some measurement of a person, such as his height, distance from elbows to the floor, or something else?

Re: Workbench Raised!

#5

Re: Workbench Raised!

Stuart Hough

Hi John! What I have read is for hand work...the top should be at a level of the base knuckle joint of your pinky. Typically, for machine work, or dovetailing and close chisel work, you should shoot for the middle of your wrist. Don't know how scientific that is, but it seemed to make sense. Of course, you can set your benchtop height to whatever feels comfortable for the work you do.

Re: Workbench Raised!

#6

Dale Lenz

Re: Workbench Raised!

Dale Lenz

My bench was built for hand planning, believe it was Ian Kirby that suggested the top of the bench should be 4" below your waist. Has worked well for me, for over 34 yrs. Did a little bit of wood carving several years back, and my back was talking to me...

Good luck.

Re: Workbench Raised!

#7

Re: Workbench Raised!

Derek Cohen (in Perth, Australia)

When I built a new bench about 4 years ago, the height was determined by the "pinky rule", as outlined by Christopher Schwarz. This led to a bench at 30" for my height of 5' 9 1/2". Keep in mind that the bench is used for handtools.

My previous bench was 32". The new bench felt good when planing, and I could lift the work with a Moxon vise when sawing dovetails. Over time, however, my back began to complain at bending lower. So, about 18 months ago, I raised the bench 2" (resting the legs on bricks), and I have not looked back since.

There are also bench-on-bench to raise work up to avoid bending at all. Carving vises are similar.

Work height is a personal matter. You need to test out a few heights and then go with what suits you best. Don't let fashion guide you.

Regards from Perth

Derek

Re: Workbench Raised!

#8

Humm. Never thought much about it but

Gary Smyth

I'm 6'1" and all of my big tools are on casters of mostly 2 1/2" (because long ago I got a box of 36 of them for maybe $20), but my woodworking stuff is much higher that that mentioned in earlier posts. The router table is 45", the table saw 40", the sanding machine working platforms are at 45", the work bench 42", my lathe center line is at 53" and both the drill press and band saw at 48". No rhyme or reason for the various heights -- they just are. I have a roll around assembly table at 30", a scissor lift that can go to 30" and saw horses at 12", 24" and 30" that rest on the floor and typically have a 3/4' sheet of ply on top when I need them. I use large lazy susans that average 2" high raising many things even higher.

I think most of my tables heights are owing to where they fit during many of my moves and what will go underneath in the way of storage. For me the heights are fine and sight lines rather than muscle power are also a factor. My take is do what is comfortable and /or necessary for the space at the time.

Re: Workbench Raised!

#9

Re: Workbench Raised!

Jim O'Connor

I set mine at the top of my hip and it has worked well, so that is the math factor that works forme.

Re: Workbench Raised!

#10

Re: Workbench Raised!

AZ in Colorado Springs

I built a Roubo-style bench about two years ago and it's 36" tall. This way it serves as an out feed for Mt table saw and it's a good working height for me (at 6' 1"). I use a combination of hand and power tools. My router table is about 42" tall. I don't want to have to lean over to change bits or do the set up.