Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Spiral jointer/planer problem

Posts

Spiral jointer/planer problem

#1

Spiral jointer/planer problem

Svante

Hi,

I have been using my Hammer A3 41 with spiral cutters for more than a year now and am very happy with the performance:

- The fence is accurate, although simple

- The cutters stay sharp for a long time

- Low noise level

- Extremely good surface

- Very little tear-out

However I have some problem when planing thinner boards (less than 6 mm or 1/4"). It seems like the cutters lifts the board making a rippled surface in the beginning and end of the board. Probably because only one of the two hold down rollers are in function. The problem can be reduced by planing at a 30 degree angle but does not disappear.

Has anybody found a work around on this?

Best regards,

Svante

Re: Spiral jointer/planer problem

#2

Re: Spiral jointer/planer problem

Barry Irby

I have a Dewalt lunchbox planer with straight knives, so my experience may not be similar to yours. Planing thin stock is dangerous because the stock lacks the strength to stay down against the platen. The knives tend to lift the end of the piece and it flutters or chatters. I have had weak pieces such as burl get lifted into the knives and just shatter or explode. I have had knots knocked out of pieces. Your spiral cutter head may have less (or more) tendency to vibrate or lift the ends.

I have fed thin stock through taped to a backer or sled. On very thin stock I have taped both ends. I used high quality double faced tape. Then the problem becomes how to get the stock off the tape without destroying it. Used lacquer thinner in some cases. Then the problem becomes how to get the last of the tape residue off the stock.

With anything I send through the planer I know that snipe may occur on both ends so if I can, I cut the rough pieces about five or six inches too long and then trim the snip off. This is not as wasteful as it sounds. Most of what I plane is starting with rough stock and there are cracks from drying at the ends and the ends were cut with a chainsaw and may be crooked. I leave that on the board as a sacrificial piece when I am doing stock prep. On lumber that is straight and flat, I run it through the planer full length to avoid the snipe that would occur on shorter pieces.

Re: Spiral jointer/planer problem

#3

Re: Spiral jointer/planer problem

Stuart Johnson

I use the drum sander when I get down this thin. I've not tried it but if you cut your pieces oversized (width and length) tacked the edges with CA onto a backer board they might go through okay without the tape issue.

Re: Spiral jointer/planer problem

#4

Re: Spiral jointer/planer problem

Derek Cohen (in Perth, Australia)

Hi Svante

I have the A3-31 and have not experienced similar problems. Just superb performance for about 3 years now.

The only issue I once had was when the bed was dirty/sticky and the rollers did not carry the board through in thicknessing mode. This was solved by cleaning and waxing the bed (I used a little Renaissance wax).

I would try this first.

Regards from Perth

Derek

Re: Spiral jointer/planer problem

#5

Re: Spiral jointer/planer problem

John in NM

I'm not familiar with the machine you have, but planing thin stock can be difficult with any machine. If there are idler rollers in the bed of the machine you may want to make an auxiliary bed for the stock to ride on, and wax it really well (you can also lower the rollers, but the aux bed is a bit easier than setting roller height all the time).

You can also try a sled that passes through with the stock being planed.

If you don't have idler rollers, I'm not sure what the problem would be - too much friction on the bed maybe? The beginning and end of a board is when one or the other of the feed rollers has to do the most work, so perhaps Derek is on to it (likely too since he uses a similar machine). I'm just not sure why it would be worse with thin stock in that case. Usually thin stock problems come from the bed rollers.

Re: Spiral jointer/planer problem

#6

Re: Spiral jointer/planer problem

William Duffield

…used lacquer thinner in some cases

If you stick it down to a backer board with contact cement or Super 77, lacquer thinner will also dissolve and release the adhesive.

To eliminate snipe, the easiest thing to do is to feed a pair of longer, narrow boards* through on either side at the same time. They need to be long enough to both engage the infeed roller before the stock and to disengage the outfeed roller after the stock has cleared.

*You find these in your drawer kicker and runner stock stash, and toss them back in there or into your cock bead stock stash when you have finished with them.

Re: Spiral jointer/planer problem

#7

How wide are your boards?


Re: Spiral jointer/planer problem

#8

Ellis Walentine

Snipe

Ellis Walentine

An old trick to eliminate snipe is to lift the end of the board as you feed it into the planer and as it exits. It isn't a foolproof method, but it works much of the time. You can also feed all pieces of the same thickness directly after each other so there's not a time when the feed rollers become disengaged and release pressure on the wood.

Ellis Walentine, Host

Re: Spiral jointer/planer problem

#9

Re: Spiral jointer/planer problem

Svante

Hi Derek and others,

I did put some wax on the bed as you suggested and to my great surprise it helped! I can not really understand why but I guess that is something I have to live with....

There is still a very minor snipe in the beginning of the board but that is no real problem.

Thanks a lot!

Svante