Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Sjoberg Bench

Posts

Sjoberg Bench

#1

Sjoberg Bench

Ivan

It is time to refinish the top of my Sjoberg workbench. I have light sanded it and now need recommendations for the sealer. They use Lacroma Clear 25 from Sherwin Williams on new benches. I have not checked with SW to see if it is available. Has lasted an amazing long time.

Re: Sjoberg Bench

#2

what is your objective

Bill Tindall, E.Tn.

Why do you want to put a finish on the bench? What do you want this finish to accomplish for you- looks, abrasion resistance, solvent resistance, etc. ?

The is nothing special about the SW finish. I expect it was used mainly because it meets the air quality requirements for where it was applied, and not because it has some performance attribute that makes it best for a bench. If you just want a varnished bench that looks close to new put any finish on it.

If I was making benches I would finish them with a high performance floor finish. But these are expensive finishes, too expensive to put on something that just needs to look good to get it sold.

Personally I have never added finish to my bench. I put a piece of 1/8" Masonite on it and change it every few years.

Re: Sjoberg Bench

#3

Re: what is your objective

Ivan

To protect the top!

Re: Sjoberg Bench

#4

Re: what is your objective

Jim O'Connor

My bench was made to be used so I just put on a coat of some polyurethane to retard stain splotches and glue drips, and it looks like it. But I'm careful to try to not cut into it with a saw or chisel , but it looks like that also. I would just go with some poly and call it good.

Re: Sjoberg Bench

#5

Re: Sjoberg Bench

don stephan

When I finished building an ash version of the Klaus bench, I wiped on two or three coats of boiled linseed oil to warm up the wood a bit. There is a ring from a wet coffee cup, but I have a separate bench with a melamine surface I use for gluing, staining, et cetera.

Re: Sjoberg Bench

#6

Re: what is your objective

AZ in Colorado Springs

Jim, does the poly give it a slick surface? Or not so much with a single coat?

My bench (2-1/2 years old) is made of Douglas Fir, and has no finish. My old bench had a plywood top and also had no finish, for 28 years.

(Ivan, I'm not trying to imply that you shouldn't renew the finish on your bench.)

Re: Sjoberg Bench

#7

Refinishing a bench

Derek Cohen (in Perth, Australia)

Ivan, as a predominantly handtool woodworker, my bench is the most important tool in the shop. I check it periodically for flatness, since this provides a reference for working on pieces. It also makes items more stable. When you noted that you had sanded your surface down, did you also check it for flatness? I would correct mine with a handplane. I would not use a sander, which is more likely to leave a depression.

Once flat, some like to leave it without a finish, or even rough up the surface a little for grip. I wipe on a thin coat of danish oil to aid in removing glue or finish than my drip.

Actually, it is time for me to do the same as you.

Regards from Perth

Derek

Re: Sjoberg Bench

#8

JL

Re: Sjoberg Bench

JL

Polyurethane or polyurethane/oil to get the glue drips off.

I know of someone who coats his with the Behlen's Rockhard.

Bill's sacrificial tempered hardboard isn't a bad idea either. I have those on my wall cabinet counter tops.

Re: Sjoberg Bench

#9

Re: Sjoberg Bench

Brian Holcombe

Flatten routinely and plane a new surface when the current one gets too ugly. Clean is important, but scratch and dent is fine so long as it does not create an effect which can damage the work.

Re: Sjoberg Bench

#10

Re: Sjoberg Bench

don stephan

If a tabletop, most people would suggest a similar finish treatment on both the upper and lower surfaces so moisture moves into and out of the surfaces more equally.

Re: Sjoberg Bench

#11

Re: Sjoberg Bench

Ivan

Thanks for the replies. I just ran over it with a fine flat sponge so as not to mess up the flatness. Just need a new topcoat to seal it from the usual spills.

Re: Sjoberg Bench

#12

Re: what is your objective

Jim O'Connor

I don't remember that it was slick, probably like a fresh planed surface.

Jim

Re: Sjoberg Bench

#13

Re: Sjoberg Bench

William Duffield

I do not sand the top of my benches, because the abrasive left in the surface will dull plane and scraper blades, which I use as needed to clean the tops. Whenever I get glue drips or other stuff above the surface of a bench top, I scrape it smooth with a card scraper. I do not put poly on bench tops, because I don't keep poly in my shop, because it is inappropriate for fine furniture. They are work surfaces, so whenever I'm finishing a project with danish oil, varnish, wax, or even shellac or epoxy*), I wipe whatever finish is left over onto the bench top (unless I need to use the bench top before the finish would have dried).

*I seldom have any epoxy left over, because I try not to mix up any more than I need for the task at hand, and I try to select a hardener with an appropriate cure time, so it has usually started to kick by the time I would be ready to wipe it on the bench top.