Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Mattress Questions.

Posts

Mattress Questions.

#1

Mattress Questions.

Barry Irby

I am making beds for my granddaughters. A friend gave me a nice but brand X mattress. It's a pillow top type and about 14" tall. It has some sort of brown fabric on the bottom and seems to be padded. There is an internal metal frame, but it is an inch or two above the brown fabric. The question is, do I put a solid bottom in the bed or are slats enough? (If slats, how many?)

Re: Mattress Questions.

#2

only a guide

Gary Smyth

From the web. "... if your current bed has no wooden slats, you can calculate the number you will need and the width of them easily. First, take the measurement of the length of the bed.

Most beds are around 80-inches long, and most slats are 2-by-1 inches. Therefore, in this example, you would divide 80 inches by 2 inches, which equals 40 inches. That means that there is enough space for 40 slats. However, you will need one slat’s worth of space between each slat, so you should divide this number in half. Therefore, you would need approximately 20 slats."

Personally I don't think you need that many, but it's a reply.

I have a antique cannonball rope bed that I use for guests. Modern mattress sizes are now a different makeup. Some time ago I had to remove the rope and in order to keep the frame I used 1/2 x 1/2 square steel tubing nested in a dado in a screwed on cleat on the inside of the original frame. I used ten lengths of the tubing and set a 1/2" fitted plywood sheet on top of them so that the top of the ply sits slightly lower than the top of the original frame. The box spring sits on the ply. Haven't given it a thought since then. No complaints, no crashes. Works for me.

Also, I looked up "bed slat kits". Amazon sells them. They don't say how many, but if you provide the size of the bed they provide some information. For a twin bed this is their information

Item Weight

20 pounds

Product Dimensions

75 x 4 x 39 inches

Item model number

128017-5010

Assembled Height

39 inches

Assembled Width

4 inches

Weight

20 Pounds

Re: Mattress Questions.

#3

More Questions......Somebody help me

Barry Irby

I have used oak 2 x 4's as slats. (I had the oak and it was free but I still don't want to waste it) It looks to me like four are string enough. I am assuming the mattress needs more support and was considering using a layer of half inch Baltic birch plywood.

It seems the rage is to put slats in covering about 50% of the area. I have never seen a bed with that many slats, but I have never done a bed without a box spring.

I was reading a blog on this and some Indoor Air quality expert said that if you put plywood under your mattress you WILL get mold because sweat can not dry out. I am struggling to believe this. How much air flow could there possibly be through a 14" thick mattress?

What is happening in the real world?

Re: Mattress Questions.

#4

Re: More Questions......Somebody help me

Dick Coers

You can get by with just a few slats when you use a box spring under the mattress. No idea what kind of structure inside a brand X mattress. What happens if you don't put in enough, just add more. Heck it was a free mattress anyway!

Re: Mattress Questions.

#5

Re: More Questions......Somebody help me

Barry Irby

Thanks, You are correct. I am over thinking this. Trying to make it easy and simple to move, because I suspect it will get moved more than once in it's hopefully long life time.

I just went and looked at Lowe's web site and they claim to have SYP 1x4's 12' long for less than $7. The ones in the picture are as perfect and straight grained and clear as any SYP I have ever seen. At most I need about 8. I'm gong for it. I want to own some wood that perfect and leave it to my grand children. Any problem I can solve for less than $50, I'm in.

Re: Mattress Questions.

#6

Re: Mattress Questions.

don stephan

What does the mattress manufacturer recommend? Not sure from your description if you have a one piece mattress/foundation or just a mattress.

Re: Mattress Questions.

#7

Re: More Questions......Somebody help me

Jim Dillon

Barry, your 1 x 4s should do just fine, at least based on my research. What I have come up with, while constructing my bed, is anything from 3/4 inch thick x 4-6 inches wide to 1 inch thick. Some advocate popular or soft maple for the slats and avoid soft woods as being too flexible. Most leave an inch or so between slats to enhance air circulation. A fine touch is to slot the slat on the end to surround a dowel on the ledger board. This prevents the slats from moving. I will probably do that. Although my current plan for my bed specifies 1 inch thick slats, I think that is overkill and will go with 3/4 inch stock and probably just use what I can salvage from my stack of wood. Sounds like you are well on your way to making a nice bed. Plywood can also be used, but I see its use more more futons etc. Good luck. Jim

Re: Mattress Questions.

#8

Jesper, Denmark

Re: More Questions......Somebody help me

Jesper, Denmark

You do need air circulation to keep the mattress dry. Slats or, if plywood, a bunch of holes. We all lose about a quart of water through sweat at night, and idoes migrate through the mattress.

Try to hop on the scales before you go to bed and again in the morning, and you can see how much you lost in water overnight.

Re: Mattress Questions.

#9

Thanks Jim....

Barry Irby

I appreciate the help. I stopped at Home Depot last night and they had 1x4 SYP 14" long for less than $4. This would allow me to cut two pieces out of each and have plenty of room to cut around the defects.

I started out to put four oak 2x4s and 1/2" plywood. The oak is very stiff. I can stand on a piece and it barely deflects.

I am considering leaving them in place and dispersing them among the pine. I think a better plan might be to fabricate a center support for the pine pieces.

I am trying to "keep it Simple" for the future owners. The fewest pieces to keep up with and assemble. Pieces that are universal and interchangeable. I have stumbled into at least one mistake. I made the rails out of 3/4" cherry. They are 6" wide and I laminated a cherry 1x2 down both edges on one side, leaving a 1" slot down the center for the slats. My thought was to insert the oak slats in the slots and then overlay with the 1/2" plywood. You have to "helicopter" the slats in. I doubt you could get the slats in if they were all strapped together like some I see. I like the idea of strapping them to keep them all together but I think it would not work here.

Thanks again for the help.

Re: Mattress Questions.

#10

Thanks Jesper....

Barry Irby

I am a little skeptical of the drying from air circulation. I slept in a water bed for forty years before giving it up for a memory foam mattress. It leaked the day before a holiday weekend about a year ago. I literally drained it and threw it out the window and got the new mattress and dumped it into the water bed frame.

So, if air circulation from below is necessary, why weren't my bed clothes soggy all those years? (not counting the leak) My understanding was that most of the weight you lose in the night is from exhaling moisture and not so much from sweating. You are correct that you lose a pound or two in the night. (I have reached the age that I lose more than that from getting up to go pee three times a night, but that's a different conversation.)

I am making a second bed for the other granddaughter and will buy a mattress for that one. So I won't have to work with the free one somebody gave me. I checked here and on line and at the mattress store for the dimensions of the bed. Was assured the mattress would be 60 by 80" for a queen. The free one is 60 by 82". Wish I had known that sooner, I would have stretched the rails.

Re: Mattress Questions.

#11

Re: More Questions......Somebody help me

Bruce, a MN Galoot

Our bed has a plywood base that I made 40 years ago. We've never, ever had a mold problem. In that time we'd had 3, maybe 4 mattresses.

Re: Mattress Questions.

#12

Re: Mattress Questions.

Ralph Lipeles

I've rebuilt several beds for my children over the years. The simplest and the sturdiest is to use a piece of 1/2" plywood screwed to the cross pieces. The cross pieces are 1 by 6's about every 1 1/2 feet.

Re: Mattress Questions.

#13

I'm skeptical of that claim too...

John in Nm

While we do lose a lot of water to sweat/evaporation over night, I'd be awfully surprised to see dry rot of the plywood as a result! :D

Seems to me that the "expert" should know that this is very different from pouring a quart of water on a mattress every morning. I would expect the mattress/bedclothes to equilibrate pretty well just from the top side, assuming of course that it's not 100% RH in the room for weeks at a time.

If you are concerned about it, a real easy way to play it safe is to drill a bunch of big holes in the plywood with a 2" hole saw.

Re: Mattress Questions.

#14

Re: Mattress Questions.

don stephan

Between the 8) and 82" lengths, one might be non standard. Mattresses don't last forever, so eventually the family member will have to choose between a very expensive custom mattress and replacing the bed frame. Might be worth considering building for standard sizes and buy a 2nd mattress if necessary.

Re: Mattress Questions.

#15

Re: Mattress Questions.

Barry Irby

You are right. I am building two matching beds for my granddaughters and a third one for my guest room. I think I will buy them nice mattresses and keep the weird one. Its as "Bainbridge" by Sleep Products. Apparently they made various mattresses for anybody who would buy them, K-Mart, Target, etc, but they appear to be defunct. Don't want to look a gift horse in the mouth, but I wish it had been a standard size.