Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Re-Saw Bandsaw Blade?

Posts

Re-Saw Bandsaw Blade?

#1

Re-Saw Bandsaw Blade?

Joe Pack

I need a bandsaw blade dedicated to re-sawing hardwoods (maple, cherry, walnut, sycamore, etc.) and exotics (purple heart, bocote, cocobolo, bubinga, etc.) for book matched dulcimer backs and tops. I need to cut to about 3/16" to finish at about 1/8". This will be on a Grizzly 17" 2.0 hp. bandsaw using a 131 1/2" blade. What suggestions do you have for me?

Re: Re-Saw Bandsaw Blade?

#2

Lenox Tri-Master

Henry Higginbotham

I previously had a Woodslicer from Highland Hardware, and it seemed very good. The Tri-Master came in a package deal with my bandsaw and the Woodslicer hasn't been used since. Expensive, but worth it.

If memory serves, the Tri-Master comes in various flavors for everything from resawing to cutting stainless plate, so be sure you're looking at the right one. I believe mine is something like a 2-3 variable pitch.

Re: Re-Saw Bandsaw Blade?

#3

Re: Re-Saw Bandsaw Blade?

Jim Dillon

Joe, another vote for the Lenox tri-master carbide tipped blade. With my first one, I resawed a lot of jatoba (brazilian cherry) and it was great. No drift at all on 10 inch wide stuff. Finally the weld broke and I bought another. I also have a Woodslicer and it doesn't compare to the Lenox. I just have Delta 14 inch bandsaw and I understand the smaller wheels may impact the life of the weld. Anyway, I love the Lenox. Jim

Re: Re-Saw Bandsaw Blade?

#4

Re: Lenox Tri-Master

Rob Sandow

Agreed. These work great. I have 2 of the 2/3 variable pitch blades that I use on a 16" Laguna. I bought one when I first got the saw, and a 2nd one I bought used at a good price so I would have a backup.

Re: Re-Saw Bandsaw Blade?

#5

Ellis Walentine

Re: Re-Saw Bandsaw Blade?

Ellis Walentine

Ditto the Tri-Master blade, although I notice that they don't offer the 2-3 variable pitch anymore in blades under 1" wide. You can do a perfectly respectable job with a 1/2" 3-pitch blade. If carbide is too expensive -- wwhich, IMO it is unlesss you're doing a lot of cutting -- Suffolk's 1/2" 3-pitch hook blades (Timberwolf) work just fine. Just keep an eye on deflection, which will cause wavy, scalloped cuts. Don't push your stock too hard for the blade to cut without deflecting.

Ellis

Re: Re-Saw Bandsaw Blade?

#6

Re: Re-Saw Bandsaw Blade?

Barry Irby

I just talked to Rick a Lenox Customer Service. He definately was not short with me. Had a lot to say. He gets a LOT of calls from people like me with Delta style 14" bandsaws with riser blocks and without. He really did not think the TriMaster carbide tipped blade was the best choice for that saw. Blade speed too fast, possibly weak frame, possible vibration from poor or worn bearings, etc. He was not a woodworker, but recommended the Bimetal blade PN 1979061, but did say the 1/2" TriMaster was available. As usual, I am left wishing I had two bandsaws, Big one for resawing and a smaller one for everything else, and enough room for them.

Re: Re-Saw Bandsaw Blade?

#7

Ellis Walentine

Re: Re-Saw Bandsaw Blade?

Ellis Walentine

The 1/2" Trimaster is a 3-pitch blade and would no-doubt do a good job, if you want to pay a buck an inch or whatever they're up to these days. I'd try a 3-tooth x 1/2" Suffolk hook blade and go from there. You'll get good results.

Ellis

Re: Re-Saw Bandsaw Blade?

#8

Re: Re-Saw Bandsaw Blade?

Bruce, a MN Galoot

I have a standard Delta 14" bandsaw without a riser block, currently with a Lenox TM carbide. It is great. I've never had a problem with it, except after that one time I hit a sheetrock screw. I had it sharpened some place in New York and it's good as new. Never had a tension problem with the stock springs. I cut mostly domestic hardwoods, ash, walnut, maple, oak, mesquite narry a problem.

For a real treat, though (and especially to save expensive wood), get the Highland Hardware Wood Slicer. It's great! Just don't use it for anything other than resawing. It's very thin and has very little kerf, so it won't saw curves worth a hoot.

Re: Re-Saw Bandsaw Blade?

#9

I'm no fan of the wood slicer

Dick Coers

Wood slicer seems to dull way too quickly when only sawing domestics. I make my own blades using whatever rolls I can find on eBay. When you have a 100' roll, you aren't bashful about making a new one!

Re: Re-Saw Bandsaw Blade?

#10

Re: I'm no fan of the wood slicer

Bruce, a MN Galoot

I have not had that problem. What I particularly like is how well mine tracks.

Re: Re-Saw Bandsaw Blade?

#11

Re: I'm no fan of the wood slicer

Derek Cohen (in Perth, Australia)



Wood slicer seems to dull way too quickly when only sawing domestics. I make my own blades using whatever rolls I can find on eBay. When you have a 100' roll, you aren't bashful about making a new one!

Ditto, Dick.

About a year ago I ordered 2 Woodslicer blades for my Hammer 4400. I had read so much about these blades being the best thing since sliced bread. Shipping to Australia makes them quite expensive.

My reference is a 3tpi bimetal (carbide) blade I get locally. I only ever use 1/2" blades, and for everything.

The Woodsclier lasted about 30 minutes before becoming dull. I was resawing Jarrah and Makore. By contrast, the bimetal blades would last me many, many hours. This was the case with both the blades. They left a fine, but not superfine finish. Of course, as a blade dulls, so it starts to wander off line. Not a good result.

I sharpen my own blades, so re-sharpening the Woodslicer is not a big deal. However, there is not much enthusiasm to do so if the blades last such a short time. The finish off the bimetal blades is not far behind. The timbers I used have a reputation for being abrasive, so I may be expecting more from the Woodslicer than is reasonable.

Regards from Perth

Derek

Re: Re-Saw Bandsaw Blade?

#12

Adam of Oakland

i use the woodslicers, yep, wear quickly

Adam of Oakland

i really liked the timberwolf(suffolks) but had an unfavorable experience with them.

I had ordered a few extra 3/4" resaw blades for my 17"grizz and one ended up being 132" which is too long. now the grizz specifies a 131.5" blade and suffolk can make such a blade to fit the machine, but the 132" one wouldn't tension correctly. I puzzeled over the blade and eventually measured it out and found it to be too long! I called and emailed them and they kept blaming grizzly for not abiding by proper standards of adjustability and whatnot. i mean, c'mon guys, i asked for 131-5 and you gimme a 132?

guy said: "it's on grizzly". he offered to re-weld my too-long one after i shipped it back to them and i was kind of dissappointed. 131.5 specifically on the web ordering form. You know, when you need to switch over to your fresh blade, you're typically elbows deep in something and this was my last fresh hoop during a project, so i guess it's my fault for only having one extra spare.

anyway, the woodslicers do work, they wear out quick, but so far, they at least are reliable and to me that's important. plus, i don't work with any super-hard woods, though i do a lot of reclaimed wood which can have hidden surprises in it, so a cheap blade sometimes makes sense to me...

bandsaw blades to me are kind of like floss, i guess.

Re: Re-Saw Bandsaw Blade?

#13

Adam of Oakland

Re: I'm no fan of the wood slicer

Adam of Oakland

I would really like a primer on how one can weld up their own blades from a spool. that seems like the ultimate economy, esp. beacuse i do so much resawing

Re: Re-Saw Bandsaw Blade?

#14

Soldering

Yonak

I became swayed by the attributes of soldering when I had a bad run of new blades break at the weld. I bought a soldering jig and some silver solder from Lee Valley and fixed all the broken blades. That was a year ago. I use my band saw a full day every week and haven't had a blade break at the soldered joint yet.

Re: Re-Saw Bandsaw Blade?

#15

Hard silver soldering

Dick Coers

It's my opinion that the flame heat from silver soldering anneals the blade a little further from the joint than the traditional upset welding and annealing. I used a primitive blade welder at work and the annealing on it was a process of bumping a button to try and maintain a low red color in the blade for a few seconds. I could get it to work, but occasionally would not get it right and the weld would still be brittle.

Re: Re-Saw Bandsaw Blade?

#16

tutorial *LINK*

Dick Coers

This one is pretty good. I do recommend a more precise scarf joint. I adjust my miter gauge over as far as I can on my disc sander to sand the longest bevel possible. Tight joints are needed for silver solder just like a good glue joint.


http://www.shakerovalbox.com/wp-content/uploads/BandSawBlades.pdf

Re: Re-Saw Bandsaw Blade?

#17

i use superCut band saw blades

del schisler

i use these and they stay sharp and don't break , i do re-saw all the time i don't get many blades , they stay sharp long time here is the link http://www.supercutbandsaw.com/

Re: Re-Saw Bandsaw Blade?

#18

Jerry Maske

Re: Re-Saw Bandsaw Blade?

Jerry Maske

You won't do better than the Laguna blades. Not only are they the best, but they are carbide tipped and CAN be re sharpened. I can resaw a 12 x 12 x 6" piece into 1/4" slabs with ease.

To be sure, Laguna blades are expensive. But when you consider that they work better than any others, last longer than any others and can be resharpened, that makes the initial cost easier to deal with.

Just my opinion.

Jerry

Re: Re-Saw Bandsaw Blade?

#19

..Not for me.

Yonak

I've had a different experience with SuperCut. My experience is that their band saw blades are prone to fail at the weld and their customer service is poor.

Re: Re-Saw Bandsaw Blade?

#20

Re: ..Not for me.

del schisler

i had a lenox blade break for me ? i guess a roll of dice ??