Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

WC Weekend Accomplishments....

Posts

WC Weekend Accomplishments....

#1

WC Weekend Accomplishments....

Dennis E Peacock

3 Oct 2016

Good Morning Everyone,

Working oncall and still working oncall. While waiting on some critical processes, I thought I'd get this off to a start for the rest of you. :)

Been working on the Phase 3 of the bowling alley project and should be done with it by Wednesday of this week....I hope.

Spent some time with family this weekend and I'm trying to teach myself about running digital sound software and new sound equipment for our church. I'll get around to the install of the new equipment once I get a hold of how all this stuff works. :)

That's it for me....other than going to the doc today about my left shoulder...been in a lot of pain for the past 9 months with it and just now getting a referral to see a doc that can tell me all about it.

So what did YOU do this past weekend?

Best of weeks to you all.!!

Dennis Peacock

Re: WC Weekend Accomplishments....

#2

Re: WC Weekend Accomplishments....

Joseph Mulherin

This past week I have put together my new garage door opener and installed same. Am going to take old one to Habitat for Humanity to use as salvage if they want it. It was first installed by me 29yrs ago.

Door will not lift using just opener....left side lifter cable needs replacing.....this week will get it done.

Re: WC Weekend Accomplishments....

#3

Making door headers/trim

GolfSteve in Calgary

Finally making some progress on my house renovation. Milled the trim for the door headers. Quartersawn fir.


Nice that the profiles stack neatly. Saves a lot of room in the shop.


Re: WC Weekend Accomplishments....

#4

Re: Making door headers/trim

William Duffield

There's no clue in your pictured how you ran the moulding profiles. Rabbet planes and hollows and rounds? Multiple simple profiles on a router table? Complex cutters on router or shaper? Some other method?

Re: WC Weekend Accomplishments....

#5

Re: Making door headers/trim

GolfSteve in Calgary

I started with 8/4 vertical grain fir (mix of quartersawn and rift sawn), trimming off 1" x 1-3/4" strips.

Each strip was milled in 5 steps; and for steps #3 and #4 I made several passes to reduce cut depth. All the router work was done in a router table.

1. Cut a small groove so that the cutter in step #3 produces a clean edge.

2. Cut most of the waste off using table saw with blade at ~45 degrees.

3. Mill the large cove using a 1" diameter bit (Lee Valley 16J19.66)

4. Mill the ogee using Freud bit 867.502.11B.

5. Cut a small rabbet at the bottom of profile using a rabbet bit.

6. Spend rest of life sanding...(actually the cuts were very clean and require little sanding).

The frieze started as 4-1/2 x 1/2" baseboard. I cut 1" off to make a 3-1/2" wide frieze, and used the 1" cut-off to form a 13/16" x 3/8" bead.


I plan to glue the crown to the frieze in the shop, cut to length/cut returns, then install in the house. I'll install the bead in the house; hopefully I can flex it enough to hide some gaps. My house is a 1970's slap it together box, and the framer who built it believed that +/- 3/4" was a tight tolerance, then the drywaller came in and installed metal edge corner protection, and slapped another 1/4" of mud on top of that...so anything that extends beyond the door opening is usually slanted, crooked, and sloped :-(


Re: WC Weekend Accomplishments....

#6

Re: WC Weekend Accomplishments....

William Duffield

I attended Hearne Hardwoods, Oxford, PA open house Friday and Saturday

hearnehardwoods.com

as an exhibitor, demonstrating for the Delaware Valley chapter of the Society of American Period Furniture Makers.

sapfm.org

We showed furniture we had made, woodworking tools and techniques, including carving pineapples, sulfur inlay, holly stringing, and making mouldings with rabbet planes, hollows and rounds, beading planes and a sticking board. Also, we showed drawing plans for furniture, work holding on meta-benches, and especially discussed benefits of membership in SAPFM.