Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Bessey clamp wont hold

Posts

Bessey clamp wont hold

#1

Bessey clamp wont hold

Terry Alexander

I have a woodcraft "knockoff" 12" Bessey parallel jaws clamp. When I am tightening up a piece....just when I get to where I am going to put a lot of pressure on the piece, the clamp gives way (not sure how to explain it). I just loses that "grip".

I am hoping that one of y'all have had the same problem and know of a simple fix. As y'all know...they aint cheap so I am in hopes of being able to salvage the clamp.

Thanking you in advance!

Terry Alexander in West Texas

Re: Bessey clamp wont hold

#2

Re: Bessey clamp wont hold

Robin Corell in Atascadero

I don't mean to be flip but clamps are one of those tools where you really do get what you pay for. Wetzlers if you can find them on the used market command a premium for a reason and Bessy's are worth the spending a bit extra for for when buying new.

Re: Bessey clamp wont hold

#3

Buy REAL Besseys.

Dick Coers

The bar is probably worn out on your Wood River clamps. That's the thing with cheap clamps, they can look the same, but the metallurgy isn't close!

Re: Bessey clamp wont hold

#4

Re: Buy REAL Besseys.

William Duffield

If you find used Jet K-bodies for sale, make sure you try them out before paying for them. A lot of the original ones would lock up if you closed them all the way and tightened them hard, and you couldn't get them to release.

Re: Bessey clamp wont hold

#5

Not familiar with the woodcraft but

Gary Smyth

the Bessey's have a reeded edge that lock the clamp. If you regularly glue up the same sizes of material glue excess fills in or partly fills in the reeded portion. If that happens the clamp will slip when tightened. Check the Woodcraft clamp to see if that is what is happening. If so, use a wire brush to clean out the reeding. If not that, it may well be the steel of the clamp.

Re: Bessey clamp wont hold

#6

Re: Bessey clamp wont hold

Hank Knight

I agree with Gary. I have a bunch of Bessy clamps. A couple of them have slipped as the OP describes. Upon examination, I found that the "reeding", the little serrations on the edge if the bar, had become either worn or filled with impacted glue, wax, etc. I tried wire brushing to clean them with no success. I tried solvents with no success. I finally solved the problem by sharpening the serrations with a few strokes with a small triangular file. It took a little patience, but it worked.

Re: Bessey clamp wont hold

#7

Re: Bessey clamp wont hold

Jim Dillon

Hi Terry,

Good to hear your voice again on WoodCentral. Agree with Hank and Gary regarding cleanliness of the bar. But, given your extensive experience, I would assume you have thought of this problem. As these clamps are fairly simple devices, I would chalk it up to experience and pick a different brand of clamp next time. I have a number of Bessy clamps that have never experienced your problem. I am also a fan of the Universal clamps. I have no experience with the Jet look-alikes. Jim

Re: Bessey clamp wont hold

#8

Re: Bessey clamp wont hold

Barry Irby

I don't have similar clamps, Bessey or otherwise. I have lots of pipe clamps. Sometimes the metal grippers that the pipe passes through lose their edge. They are supposed to have sharp square corners inside the circle. If the edge gets rounded they don't grip well. You can turn them over and use the other side. After that you can file or stone them to restore the edge if you are really careful.

I would look are the serrations as Gary and Hank suggest and at whatever the paul is that grips them and see if it can be turned around or sharpened. Beyond that, I am suspicious of the metallurgy.

Re: Bessey clamp wont hold

#9

Re: Bessey clamp wont hold

TomD

Get a checkering file, or anything similar, and reestablish the reeding.

Re: Bessey clamp wont hold

#10

Re: Bessey clamp wont hold

les winter

Contact woodcraft. They may simply replace them for you. I had a similar problem with a few Bessey's. They were 10 years old and Bessey replaced them. The only issue was they wanted to see the failed clamps and verify for themselves that no pliers or wrenches had been applied.

Re: Bessey clamp wont hold

#11

ebd

Re: Bessey clamp wont hold

ebd

I have never had any clamp fail under pressure that won't create a glue failure. How much pressure are you applying? Clamps can apply a far higher pressure than is optimal for a glue joint. Could you be cranking the clamp far too much?