Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

A table is underway

Posts

A table is underway

#1

A table is underway

Bill Tindall, E.Tn.



Years ago I bought a Moroccan marble table top with fossils in it. Finally have gotten around to turning it into a table that will go in the sunny dining room. We will set plants on it and maybe serve off it as needed. Or it will just accumulate stuff. I just made a table frame and will simply set the marble on top.

The legs are M&T into rails. I hand chopped the mortises. I finally tried band sawing the tenon cheeks and now I see why that approach is popular.

The legs were band sawed then spoke shaved smooth with the LV shave, which I like. It has nice handles. I sawed one arc, taped the cut-off back onto the leg and then sawed the remaining arc. The result is a good looking leg and three strange looking pieces of scrap.

An experienced woodworker was watching me band saw the other day and was puzzled by my technique. It works for me and I can split the pencil line if the lighting is good. I ride the back of the blade along the kerf and pivot from this point into the pencil line as I make the cut. I aim for any error to fall outside the line. If I drift from the center of the pencil line after sawing for an inch or so I back up, and again pivoting from the back of the blade against the kerf, resaw the section in error with a light shaving cut. Watching, it looks like I am periodically gong back and forth as I progress along the guide line. When done all I have to do is shave off the teeth marks.

The stain is made from 100 parts General Finishes conditioner (the solvent they use to prepare their oil stains), about 15 parts linseed oil and about 15 parts burnt umber artist oil pigment. Stain is applied with the rubber shown in the picture, and the result wiped with a clean rag. Applied this way, it took only 10 mL of stain to do the whole table and little was removed by the rag.

Re: A table is underway

#2

Re: A table is underway

Barry Irby

Thanks for posting. Its beautiful. I am struggling with the legs. I thought my eyes were have some sort of parallax problem. Your explanation that they are curved relived my worried mind. Any chance of a straight on shot? So I can understand the curves better?

Re: A table is underway

#4

Re: Your wish is my command

Barry Irby

Thanks, that helps. I reread my post and dicieded I can't spealle.

I like the legs. My eye says they should have been slightly more slender, maybe an 1/8" thinner. Maybe that's just the rather slender rail tricking me. It will be interesting to see this with the top in place. OTOH, its your table and your design and if it looks right to you, it is right.

Re: A table is underway

#5

Leg, version 3

Bill Tindall, E.Tn.

Leg version 1 was 1/8" more slender. Rejected by the Queen of home décor. Rev. 2 was 1/16" more slender. Again rejected. I think you get the picture........

Re: A table is underway

#6

Re: Leg, version 3

Barry Irby

You are a very smart man. Not the hill to die on. There will be other opportunities for correctly made legs. (don't give the decorating department my address, please)

Re: A table is underway

#7

Re: Your wish is my command

William Duffield

Putting on the heavy marble top should make the heavier legs look more appropriately sized. Pleasing proportions don't just come out of thin air. There are structural and strength reasons and ergonomic reasons that a design looks pleasingly proportioned.

Re: A table is underway

#8

Re: Leg, version 3

Bill Tindall, E.Tn.

The legs in the first picture may look fatter to you than they are in fact. The edge of the leg is indistinct so that the front face and projected side may appear as the width of the front face. In real life the leg size looks just right to me. The thinner versions look too dainty.

I spent a lot of time on the rail height too, maybe needlessly because it will be largely obscured by the top in this low table.

Re: A table is underway

#9

Adam of Oakland

^^^Yep

Adam of Oakland

I like what william said about the need for thicker legs once the top is on there...looking forward to the completed picture.

I also love the curve you made into the legs. it imparts some verve into them, like real legs, like lithe, muscled legs. pro cyclists have these :-)

Re: A table is underway

#10

Question on mixing stains

jessecloud

When you mixed the stain, were the proportions based on weight or volume?

Re: A table is underway

#11

Re: Question on mixing stains *LINK*

John in NM

I doubt it will matter much for this kind of application, but given the proportions a $20 postal scale from Walmart or where ever seems like the way to go.

If you want to try making stains, you have two great sources of pigment in Albuquerque - cans of Japan colors from Benjamin Moore on Lomas and El Rey stucco pigment can be bought at New Mexico Plaster Supply on 4th NW. The stucco colorant is probably a lot cheaper, but since it is intended to produce a consistent marketable color when mixed with stucco, it is less intense than using pure raw pigment or Japan colors.

There's also a mail order place I liked a lot out of Tucson, they are geared more towards artists but have a wide selection of neat colors.

This is all the result of my dislike for house painting :D We colored the lime plaster on our house with pigment mixed into a whitewash of lime and water. There is about zero prep work to do, just whitewash on another coat when needed (rarely). We ended up using the stucco colorant due to cost and the area involved, but I did find that place in Tucson and filed away the info for future reference.


http://www.earthpigments.com/

Re: A table is underway

#12

Thanks John.  Great info!


Re: A table is underway

#13

weight

Bill Tindall, E.Tn.

but the amounts are approximate so it doesn't make any difference.

I have a small scale I use for cooking. I convert recipes to weight amounts and simply weight ingredients into the mixing bowl. Saves time, dirty measuring devices and it is more accurate.

I do the same with stain. I just weigh components into a small cup. BTW, the stain darkness can be adjusted by the amount of pigment added. I have used as much as 25 parts pigment.

Re: A table is underway

#14

caution

Bill Tindall, E.Tn.

the finely ground artist pigments as well as Japan colors are preferred. I just started using artist pigment and I like the fineness of the grind and the handiness of the tube. It colors nicely. I bought loose pigment from Lee Valley and it is too coarse.

Re: A table is underway

#15

Re: caution

John in NM

I bet the stucco color would be too coarse as well. Good to know.