Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Heavy duty mobile base hardware?

Posts

Heavy duty mobile base hardware?

#1

Heavy duty mobile base hardware?

John K Jordan

I am looking for a means to occasionally move a milling machine. The total weight will be over 800 lbs.

I'm welding up a heavy steel base. If I can find them I would like to attach some kind of caster that can be retracted so the base (and levelers) will sit firmly on the concrete floor when not being moved. Most of the mobile base hardware I've looked at is not rated for enough weight or does not even list the weight limit.

I'm willing to use a pry bar or build some type of a jack if needed but I'd rather have casters permanently attached rather than have to slide something underneath. It would be best not to have to tilt the machine much.

Any ideas or places to look? Some industrial solution?

JKJ

Re: Heavy duty mobile base hardware?

#2

Re: Heavy duty mobile base hardware?

Joseph Mulherin

You might try looking at www.casterconcepts.com. They have movable casters which might be just the thing you might like.

Re: Heavy duty mobile base hardware?

#3

Re: Heavy duty mobile base hardware?

garthinsandiego

Might look at Wesco Rais-N-Rol Machinery movers available through MSC. Several models available up to 10,000 pounds. The advantage is that they are not dedicated to a single machine. Sold in pairs and only need some clearance under load to insert the forks. Not inexpensive, but I've used these before and they work well. Maybe can find used for less money.

Another option is to permanently mount casters or roller skids to your base and use floor locks to keep in place until you need to move the mill. Roller skids are more expensive, but have a lower profile. Again, MSC (and others) has several to choose from.

I've also raised casters off the floor using a pry-bar and inserted shim blocks under the corners of the base. Casters only need to just clear the floor to keep the machine in place. With provisions for this built into your base you wouldn't need to lift each corner more than a 1/4" or so.

No matter what method you use to move the mill you will still need to use a pry-bar to insert shims to level it after moving.

Hope this helps.

Re: Heavy duty mobile base hardware?

#4

Re: Heavy duty mobile base hardware?

John K Jordan

Thanks for the link. There are more kinds of high quality casters than I imagined!

I also found that SawStop makes a mobile base for their industrial saw that might work. It allows the machine base to sit firmly against the floor. To move, a foot pedal activates a small hydraulic jack which lifts the entire base off the floor and puts the load on the casters. After moving, a release lever slowly lowers the machine back to the floor. I looked at the exploded parts diagram and it is a clever design.

This sounds perfect for my application, about $300, good for 1000 lbs. I could build my mill base to the same dimensions as the industrial saw base so it will fit perfectly.

JKJ

Re: Heavy duty mobile base hardware?

#5

Re: Heavy duty mobile base hardware?

Joseph Mulherin

glad you found the base you might use. the price is a little over my thinking, but the hydraulic lift will be a great aid in moving the equipment around.

Re: Heavy duty mobile base hardware?

#6

Re: Heavy duty mobile base hardware? *LINK*

Bob Entwisle in NJ

John,

These look interesting..

Bob in NJ


http://www.mcmaster.com/#casters/=9nxxqtlywris9n2kct

Re: Heavy duty mobile base hardware?

#7

Re: Heavy duty mobile base hardware?

walta

The best option may be to weld a stand for the machine to sit on like a pallet. Then get a pallet jack and move the machine whenever you want.

Walta

Re: Heavy duty mobile base hardware?

#8

Re: Heavy duty mobile base hardware?

John K Jordan

A pallet jack would be so useful but I don't really have the floor space in the shop to maneuver (or even store) one. The tight space where I have my machining is the reason I want to make the larger mill mobile.

I like the idea of casters and leveling feet that can be cranked up and down. More research ahead. Thanks to everyone for all the ideas to consider. I suspected there were more options than what I found at Northern Tool!

Re: Heavy duty mobile base hardware?

#9

Re: Heavy duty mobile base hardware?

William Duffield

I love my SawStop industrial mobile base. It's probably just what you are looking for. The Industrial SawStop and the mobile base weigh almost 800 lb. I can move mine in any direction with one hand, lift it with two steps with one toe and set it back firmly on the floor with one step.

Note that the base of the Professional SawStop is smaller (about 4" or 5" shallower) than the base of the Industrial model. SawStop has made some modifications to the linkages of the base to accommodate the smaller saw, at an additional cost. If your milling machine base is a different size than the Industrial SawStop base, you would do well to study the modifications that are needed for it to fit the Pro model.

Re: Heavy duty mobile base hardware?

#10

Re: Heavy duty mobile base hardware?

John K Jordan

>>> If your milling machine base is a different size than the Industrial SawStop base, you

>>>would do well to study the modifications that are needed for it to fit the Pro model.

Thanks. I haven't built the mill stand yet so I can easily make it to fit. I'm leaning towards this mobile base due to the design and ease of use. If I go with it I'll probably buy the mobile base first then build the mill stand to fit. I'm glad to hear your evaluation.

I'm designing the base to use heavy-wall rectangular tubing and some 1/2" steel plate I have on hand. Years ago I bought about 8000 lbs of steel stock at scrap prices - it sure is nice to walk over to the shed and pull out pieces to fix or build something instead of going shopping! (Full 20 and 40' lengths of heavy-wall steel are expensive and a pain to haul.)

JKJ

Re: Heavy duty mobile base hardware?

#11

Re: Heavy duty mobile base hardware? *LINK*

William Duffield

The frame of the SS mobile base is made of 1/4" thick steel "L"s, welded together at the corners. The base of the saw sits on this frame and is supported all the way around. When the base is dropped, the frame sits flat on the floor, and the bottom of the saw sits flat on the frame, so the saw is only 1/4" above the floor, and that quarter inch is all steel al the way around. The rotating casters are on the corners of another enclosing frame with articulated joints at all four corners. The bottle jack effectively pulls the frame with the attached casters downward, lifting the frame supporting the saw, so the saw stays level and stable at all times and only needs to be lifted far enough to clear whatever debris is on the floor. All you should have to do is cut a sheet of steel to drop into the frame, and set the mill on top of it, and probably bolt it down.


Industrial Mobile Base Owner's Manual

Re: Heavy duty mobile base hardware?

#12

SawStop industrial mobile base

John K Jordan

Thanks. I found that manual yesterday and was impressed by the mechanism and design from the specs, pictures, and exploded parts diagram.

Do you know where to find the best deal on such a base? Sir Google tells me WoodCraft and Zoro have the best price.

JKJ