Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Fastening a top with traditional pocket screws

Posts

Fastening a top with traditional pocket screws

#1

Fastening a top with traditional pocket screws

Bill Tindall, E.Tn.

Fastening a top with traditional pocket screws

I learned this technique from Steve Hamilton. I will illustrate the steps while not attempting to flaunt the result. Steve’s handiness with a carving chisel greatly exceeds mine so his results look better. I will be attaching the top and base to the bed side chests of drawers using pocket screws. Illustrated is making a pocket in the base frame.

The problem is how to get the pocket located so the screw sticks out the right amount, and not through the top. :( Easy as it turns out.

1. Drill an angled hole in the apron. PIC1



2. Align the screw to be used so that the desired amount sticks above the apron (the part that will embed in the top to hold it on) PIC 2



3. Mark the location of the screw head on the apron.

4. Drive a chisel into the apron at the location established in step 3. This operation locates the bottom of the pocket. PIC 3



5. Carve out the pocket up to the flat established by the chisel cut with a gouge. Pic 4


Re: Fastening a top with traditional pocket screws

#2

Nicely Done!


Re: Fastening a top with traditional pocket screws

#3

Re: Fastening a top with traditional pocket screws

Mike Circo

There is a risk there. Using a "bugle head" or flared shoulder screw could cause a wedging action when tightened down and blow out the pocket. Traditional pocket screws have no flared shoulder. That is the reason for creating the flat at the top of the pocket, to mate with the flat on the screw head.

Also. How do you allow for wood movement in the top? Trapping the top on all four sides with screws could cause cracking later in the top's life.

Re: Fastening a top with traditional pocket screws

#4

Take a peak in old furniture

Bill Tindall, E.Tn.

It is screwed down with flat head screws in loose pocket holes. I have never seen a table top fastened otherwise in furniture older than what is considered modern.

The bottom line is that what you state is theoretically correct, but in practice it is not a problem as evidenced by the way tops were fastened to aprons since screws were invented.

Re: Fastening a top with traditional pocket screws

#5

Re: Fastening a top with traditional pocket screws

John McGaw

I'm wondering why one shouldn't use the regular Kreig jig for this? There is a goodly amount of depth adjustment available by moving the drill stop and the jig position and if this is insufficient it is always possible to use different screws than the regular Kreig square-head variety.

Re: Fastening a top with traditional pocket screws

#6

Re: Fastening a top with traditional pocket screws

Barry Irby

I agree with Bill that this is the traditional way this has been done Many times for many years. I also agree with the comments about the counter sunk screws. Pan head screws or washer head screws would be better. And I agree that the Kreg jig makes this trivial. They are adjustable and the screws are available in differing lengths. I have used mine for this many times. Works well. Reliable and quick.

I can not imagine why Hepplewhite, Chipendale and the boys of old did not use the Kreg jig. All they had to do was look it up on the Internet. That's where Jefferson got the original draft of the Declaration of Independence.

Re: Fastening a top with traditional pocket screws

#7

The answer

Bill Tindall, E.Tn.

I am too cheap to own one.

Re: Fastening a top with traditional pocket screws

#8

Re: Take a peak in old furniture

don stephan

You seem to be saying woodworkers never need to allow for seasonal wood movement, and I don't know why. Would you allow for wood movement when fastening dining table top to rails? When attaching breadboard ends to blanket chest top?

Antique secretaries I saw at local art museum all had splits in lower sides because drawer runners were hard fastened to the sides, what we now call classic cross grain construction. Must not have been a problem in the days of fireplace heat, no air conditioning, and drafty buildings when humidity level more consistent through the year, or they would not have done so.

If conditions of this build minimize seasonal wood movement, great, but please keep in mind that a novice woodworker might read this thread next week.