Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

A problem with finishing the recent walnut pieces

Posts

A problem with finishing the recent walnut pieces

#1

A problem with finishing the recent walnut pieces

Bill Tindall, E.Tn.

A problem with finishing the recent walnut pieces

When scuff sanding the first coat of finish there are a lot of white finish particles generated. Picture 1



Picture 1 shows the test piece I always carry through a finishing project to avoid surprises.

Typically these white particles are blown off and it doesn’t matter if some are left in the pores. If the finish wicks into these white pores the white disappears as seen in the second picture.



However, one set of drawers was made from a board that was more porous than usual. The white stuff stuck tenaciously in the pores. When I came back with the second coat it bridged some pores and left white in these pores. It did not look good. The solution was to thin the finish even more to lower its viscosity. Thinning enabled the finish to wick into the pores of the drawer front and the white was gone. PIC 3

Had this fix failed I would have waxed with dark wax to fill the pores with dark pigment.


Re: A problem with finishing the recent walnut pieces

#2

Clint Searl

Re: A problem with finishing the recent walnut pie

Clint Searl

I don't know if successive coats of catalyzed solvent lacquers will burn in, but I find that one-part solvent CAB or NC lacquers don't need to be scuffed between coats. Increasing reduction will level and build as appropriate.

Re: A problem with finishing the recent walnut pieces

#3

not scuffing for adhesion

Bill Tindall, E.Tn.

The first coat sets up all sorts of prickles that need to be mowed off with sand paper to get a smooth second coat.

Re: A problem with finishing the recent walnut pieces

#4

Clint Searl

Good point...

Clint Searl

I do hit the first coat with a maroon pad and blow down.

Re: A problem with finishing the recent walnut pieces

#5

sanding with a pad

Bill Tindall, E.Tn.

Maroon is too coarse for my finish. The scratches don't fill with the next coat.

I use gray.

The advantage is that the pad picks up most of the dust and it doesn't pack in the pores. However, the pads are not as effective at flatting a surface that has a lump here and there where finish has wicked up around a particle of junk. I use sand paper on high end work and pads for stuff like house trim.

Re: A problem with finishing the recent walnut pieces

#6

Clint Searl

Re: sanding with a pad

Clint Searl

The maroon pad knocks down the nibs just fine. Its "coarseness" cuts off any pimples and is eliminated by subsequent coats. But different strokes for different folks.

Re: A problem with finishing the recent walnut pieces

#7

Re: A problem with finishing the recent walnut pie

don stephan

If you raised the grain with distilled water and knocked down with light sanding when dry, wonder if the first coat of finish would still have the wood frizzies.

Re: A problem with finishing the recent walnut pieces

#8

A Good Shop Vac

Mark Mandell - Gone Round In New Jersey

with a brush would remove about all the dust. A blow gun and 100psi works well also.

Re: A problem with finishing the recent walnut pieces

#9

Jim DeLaney, Austintown, Ohio

Re: sanding with a pad

Jim DeLaney, Austintown, Ohio

I like the Mirka pads. The 1500 'grit' stuff works great between coats.

Re: A problem with finishing the recent walnut pieces

#10

Re: A Good Shop Vac

Barry Irby

I agree with the shop vac and brush idea, but as a note of caution, be careful using the compressed air. Under some conditions they either spew moisture or they cause condensation on the surface. Its a good idea to have an air line dryer in the line and pay attention to the weather. Also, I some bitter experience with an air line that had an oiler in it for air tools. A little oil goes a long way in lacquer.