Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Installing drawer slips

Posts

Installing drawer slips

#1

Installing drawer slips

Bill Tindall, E.Tn.

PIC 1



A drawer slip is a feature of English drawers. It is the “extra” piece seen in Picture 1. Its function is to provide additional bearing surface enabling thinner drawer sides and a lighter weight drawer. It also has the groove that captures the drawer bottom.

PIC 2



Slips do not have to add significant time to drawer construction. I prepare 5/4 poplar blanks about 2 ¼” wide. The groove for the drawer is milled into 4 sides of the blank and the corners rounded. This piece is then sawed into 4 slips.

PIC 3



Installing the slips is easy and reliable. I have on hand a piece of wood, the walnut piece in the picture, that fits snugly into the groove. This piece functions as a temporary bottom to align the slip. The slip-to-be is positioned with this alignment aid and a line drawn across the drawer side to mark the waste to be removed from the slip. Waste is trimmed almost to this line by any means handy. I often use the jointer.

PIC 4



Glue is applied to the back of the slip, it is aligned with the alignment block and clamped in place. The clamps don’t have to stay on long; 15-20 minutes is sufficient. When the glue is more cured, about an hour, the slip is planed flush with the drawer bottom.

PIC 5



The finished result is shown in Picture 5. A subtle benefit of slip installation as I have shown it is that the drawer grooves will be in perfect alignment. Perfect alignment is not always achieved when the grooves are cut in the drawer sides before assembly.

Re: Installing drawer slips

#2

Re: Installing drawer slips

Brian Holcombe

Nice work Bill!

I was certainly looking for you to make a front slip! Hehehe.

Re: Installing drawer slips

#3

Re: Installing drawer slips

Derek Cohen (in Perth, Australia)

Hi Bill

I did a couple of things differently in my recent build.

Where you use a spline to align the slips with the front groove, mine use a tenon ..


You may notice that I also laminated harder Jarrah to the (softer) Tasmanian Oak slip as the drawer blades were also Jarrah.

The drawer bottoms are rebated to fit flush with the slips ...


... and the tops of the slips are beaded to transition into the drawer bottom ...


Regards from Perth

Derek

Re: Installing drawer slips

#4

some comments

Bill Tindall, E.Tn.

Posts are more useful when others show alternate ways of accomplishing the same goal. Thanks for responding........

As I understand the situation your use of a tenon on the end of the slip is conventional, authentic or whatever it is to be called.

I am finishing up three cases with drawers and a large double chest of drawers is in the queue. I'm motivated to take labor out of drawer making and the elimination of the tenon on the end of the slip was a place to save time without sacrifice. In fact, given the errors that seem to creep into my tenon making the spline alignment piece provided me a more reliable alignment in the end.

Some drawers will benefit from a slip construction as you describe that yields a flat bottom drawer. A desk drawer comes to mine. However, a place to store socks, or any other squishy contents, would not mind the construction I used which is quicker to do. I have had so many problems with construction of the two Danish Modern Inspired pieces that I long ago passed the inclination for adding details that called for more fiddly fitting.

Having learned from making these two pieces I could repeat them in half the time. But I don't like Danish Modern, inspired or not, so I hope to never need the experience gained. And if I do I will be buying a Domino tenon maker in spite of the cost.

Re: Installing drawer slips

#5

Ellis Walentine

Two things

Ellis Walentine

First, thanks to both you and Derek for such illuminating posts. Secondly, good tip about planing the bottom of the slips flush with the bottoms of the drawer sides, and the other time-saving techniques you have figured out.

Ellis

Re: Installing drawer slips

#6

Re: some comments

Barry Irby

Somewhere along the way I read/learned the drawer side was "supposed" to be softer than the runner it slides on. You have noted that as well, saying that it is easier to repair the drawer than the blade or runner. A second reason was that two dissimilar woods have a lower coefficient of friction than two identical pieces. Do you have any experience with this thought? In the few chests I built I tried the use straight grained wood for both and harder wood in the chest.

Do you think adding the slip will have any impact on the drawer sliding? You are increasing the surface area of the contact.

On one older piece I got to look at for a few minutes the drawer sides were about 5/16" thick and the slips were about a 1/2 or 5/8". The slips had worn badly and the drawer sides had cut grooves into the blades/runners.

Re: Installing drawer slips

#7

Re: some comments

John McGaw

I don't know how it will work out in the long run as none of my furniture is old enough to vote yet but I've always used the hardest wood on hand for the contact parts of drawers -- hard maple sides and rails most often although I once added a strip of hard maple to the poplar sides of some drawers. A bit of heat, paraffin, and polishing on the contact surfaces makes them slide well even under load and I can detect no wear on any of the parts yet. I can see where additional contact surface might be useful but I don't know if I'm into permanence enough to do the extra work for someone 200 years down the road.

Re: Installing drawer slips

#8

Danish Modern

Brian Holcombe

Bill,

Can you point out the original work and maker? You refer to this as Danish Modern but frankly I go not recognize the style as such. I can't speak for everything in the category but frame and panel is not especially common in Danish modern or modern at all.

Here are two photos of shoji that I am currently building. The stiles are 30.5mm sq and the rails are 29cm by 45 and 60 top and bottom respectfully. Even without glue these are very sturdy at an overall of 49" talk by 32"~ wide.

The joints are double tenons, half the width of the rail is an 8mm haunch and half is a 20mm tenon. The shoulder is mitered.



Re: Installing drawer slips

#9

Easier to replace the runners IMO

Brian Holcombe

In my opinion it's easier to replace the runners. Probably better stated that in my builds I make the runners easier to replace.

I'd rather not rebuild a drawer, instead much easier to scrap the runner and replace it.

Re: Installing drawer slips

#10

Re: drawers co-efficient of friction

Rum

I've read the co-efficient of friction argument several times and would be interested in seeing more direct supporting evidence (either way) as to how useful/important it is.

I understand that dissimilar materials have a lower co-efficient of friction, but haven't been able to find any engineering tables that show the difference for dissimilar woods (this would be interesting for a variety of reasons..).

I'm also not entirely sure how much the co-efficient of friction change translates into increased wear versus simply using the hardest materials easily available for both the slip and the runner. That is does putting a soft slip on save enough wear on the runner to justify the cost of more frequent slip replacement requirement (if you are going for the archival quality product so to speak)?

I’m certainly not disputing the truthiness of the statement, but having better numbers (or any numbers really) would be at least academically interesting.

Re: Installing drawer slips

#11

Not in conventional construction

Bill Tindall, E.Tn.

Fixing a worn drawer is a trivial matter in Period Furniture. It is done routinely. To wit:

plane the bottom edges of the drawer to make a good glueing surface. Glue on a tapered piece of wood to replace what is missing. Plane to fit.

What isn't easy is fixing a worn divider. In English furniture when the white oak drawer side saws into the soft mahogany divider the worn divider can be filled with a patch but it usually shows.

Re: Installing drawer slips

#12

Re: Danish Modern

Bill Tindall, E.Tn.

It is not frame and panel.....it is post and panel. Frame and panel was common around 1700 +/- and I have built in this style in my Chester County pieces. It is much different construction than post and panel.

My artist friend who seems to be an expert in more modern furniture sent this picture and called it Danish Modern.

The problem is what was proposed by daughter was some modification of simple to make post and panel Danish Modern. The damn thing had a base on it so the posts didn't go to the floor and an extra shadow line at the panel ends. What I wound up with isn't anything. The top is "enhanced" post and panel and if the post went to the floor, and they would have if some changing horses in the middle of the stream had been done before the top was built, it would look like the picture. I think I will call my style "Rescued" for it was rescued from something that wasn't going to work.

Re: Installing drawer slips

#13

American Modernism

Brian Holcombe

Is more likely, especially for that cabinet which looks like someones take, in wood, on a famous credenza by Florence Knoll. It's quite nice looking.

Danish Modern cabinetry is very often a plywood carcass on a wooden stand or legs.

The 'President' credenza by Hans Wegner, is in my opinion, the iconic look of Danish Modernism WRT case goods.

Similarly the style which Finn Juhl created is also largely representative of Danish Modern.

I'm off on a tangent.

Anyways my larger point was that these pieces can be created in a way in which they are sound structurally. The shoji provides an example of that, those are otherwise skinny frames that are very strong.

You said previously that you did not think a substantial joint could be created in this build, but yet when look at how Shoji is built you can see that every component of the build contributes to the strength. The double tenons, the haunches and the mitered shoulder.

I pointed at other examples previously where some Chinese Ming and Sashimono furniture were utilizing spear shouldered tenons to strengthen a small joint.

A plinth can also be made quite sturdy.

Re: Installing drawer slips

#14

Re: Installing drawer slips

Pgrover sc.rr.com

Using drawer slips will allow your drawer sides to be thinner which will make hand dove tails easier to cut.I made sides 3/8 or 7/16" wide Paul

Re: Installing drawer slips

#16

Explaining again

Bill Tindall, E.Tn.

The original piece, described in a blurry picture, was essentially the upper part of the case I built. This piece sat on a base of 4 short legs (about 4" tall) connected with rails about 1 1/4" tall. The legs were significantly fatter than the 1 1/4" posts in the case above this base. The base had additional adornments that made it look nice except for the fat legs. In hindsight, the fat legs enabled secure M&T joints for the rails.

I built the case with conventional M&T and dovetail joinery. I could have built it vastly faster with floating tenons, and would if I ever build another.

Then I mocked up the base just in time for daughter to visit. She took one look at the fat legs and said she wanted them the same size as the posts above, 1 1/4". Had that decision been made in the beginning I would have extended the posts from the case to the floor so the posts framed the panel and provided a leg. It would all have easily come together with conventional M&T joinery. But, now with this horse changed in the middle of the stream I was faced with building a base from 1 1/4" legs and 1 1/4" tall rails.

If you can securely attach 4- 4" tall by 1 1/4" legs to 1 1/4" rails with your Japanese joinery I would like to see the joinery plan. Securely means this leg and frame assembly has to support a moderately heavy case above it and survive potentially sliding said case across the floor, carpet, whatever.

Faced with this engineering dead end I put a different base on these pieces.

I don' know much about modern furniture designs and less about Oriental design. I don' t like either. But an artist friend seems to be an expert in the area. She called her credenza I showed in the picture "Danish Modern" and sent me the picture because she said what I was building was essentially Danish Modern. Whatever......... The stain goes on it tomorrow and I call it nearly done with.

Re: Installing drawer slips

#17

Re: Explaining again

Brian Holcombe

Thank you for explaining further. As you mention in your reply to a different post of mine...a picture is worth 1000 words, and so I've remained somewhat confused on exactly what you were describing the first time around.

I see your dilemma, it is certainly frustrating when someone changes their mind mid-way through a project (and usually loved ones are the few who can get away with it) especially with critical and structural elements.

I like the plinth style base you ultimately decided to use.

Re: Installing drawer slips

#18

Re: Explaining again

jessecloud

At this stage in the project, its a moot point, but maybe you are underestimating the strength of a well made mortise and tenon. Chairs use m&t for most of their joinery and undergo enormous stress - e.g. the fat guy leaning back in the chair so only the back legs carry his entire weight.

1 1/4 square would be huge for a chair.

On the other hand, I share your dislike of Danish Modern and its evil cousin Mid-Century modern. I'm doing an MCM style project for a friend and it grates on my nerves to work on it. But I think its going to make her happy and that's the real point of all this!

Re: Installing drawer slips

#19

If you dislike Danish Modernism

Brian Holcombe

...I'd venture a guess that you don't actually understand the full breadth of the category.

I see, so often, ubiquitous plain looking furniture called Danish Modern when truly it is not or it is an inferior sort giving a bad name to an otherwise fine group of furniture.

So if you dislike Danish Modernism, please look up;

Finn Juhl's model 45 and 46 chairs.

Ole Wanscher's colonial chair and daybed.

Hans Wegner's Peacock chair, PP501, valet chair, and papa bear chair.

Mogen's Koch bookcase system (especially the ones with doors!), his folding chair and especially his wing back chair.

I can continue to list of names that have created absolute masterpieces of industrial design, but finally Kaare Klint's Safari chair, along with his sofa's for CB Hansen.

If you can dislike all of this, then I expect you also dislike much of American craft which took it's influence from the Danish and Bauhaus.

Edit:

Oh and here is one I forgot to mention, it sits across from me while I type this;


Re: Installing drawer slips

#20

Re: If you dislike Danish Modernism

jessecloud

Ouch! You got me good! I feel like a total philistine in regards to Danish Modern. Thanks for sharing the references. The only one I knew was Hans Wegner. I can see how the style must have felt fresh and daring at the time with the hopes placed in modernity to get past the trauma of WWII. I would think that in America, Eames is a close parallel, being deeply rooted in industrialism and the new techniques developed in WWII for processing plywood that gave rise both to the Spruce Goose and to the Eames chair.

And yes, much of the work inspired by the Bauhaus leaves me cold.

But "liking" something is a matter of personal taste, and I don't apologize for not liking much of the work done in this style. To me it seems brutally industrial, better sourced from a factory than a craftsman's workshop. Even Wegner's graceful chairs required specially designed cutters and tooling. When I look at many of the images, my first thought is of institutional waiting rooms with dozens of them in formation.

I hope my personal dislike of the style is not taken as disrespect for those who do like it or for the designers who worked in the style. I also dislike Brussel Sprouts, but have no bad feelings toward the farmers who grow them.

Re: Installing drawer slips

#21

Re: If you dislike Danish Modernism

Brian Holcombe

Anytime, but I didn't post it as a 'gotcha' more in hopes of removing the unfair brand I think Danish Modernism has after years of people making terrible copies of great work. Your dislike of the style does not bother me so much, but I have a feeling most who turn their nose up at Danish modern have misconceptions about it.

I originally had the same opinion, but once I dug a little deeper I began to have a lot of respect for the work being done. Take, for instance, the Mogens Koch bookcases still made with handcut miter edge dovetails....quite literally you see people in Rud Rasmussen chopping with chisel and mallet to make those cases. For all the complaint of mass production I bet very, very little furniture is made to the quality in todays world on the whole, especially at that scale of production where their furniture is able to be ordered through design houses.

Wegner's chairs are impressive, the wishbone chair for instance which is likely the most ubiquitous is actually quite a wonder in my eyes.